Poulan PR10527ESA Assembly / Pre-Operation, Remove Snow Thrower From Carton, TOOL BOX See Fig

Page 5
ASSEMBLY / PRE-OPERATION

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels fl at.

3.Remove all packing materials except plastic tie holding speed control rod to lower handle.

4.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD

RETAINER

SPRING

SPEEDSPEED

CONTROL CONTROL

BRACKET LEVER

FIG. 2

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL PR10527ESASafe Operation Practices for Snow Throwers SAFETY RULESTRAINING PREPARATIONCUSTOMER RESPONSIBILITIES MAINTENANCE AND STORAGEPRODUCT SPECIFICATIONS SERVICE AND ADJUSTMENTS PARTS PACKED SEPARATELY IN CARTONSAFETY RULES PRODUCT SPECIFICATIONSHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andCHECK TIRE PRESSURE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and KNOW YOUR SNOW THROWER OPERATIONDeflector remote control lever - used to change the MEETS A.N.S.I. SAFETY REQUIREMENTSDrive speed control lever - used to select forward or Recoil auxiliary starter handle - used for starting theSTOPPING HOW TO USE YOUR SNOW THROWERTO USE FUEL SHUT-OFF VALVE See Fig TO USE THROTTLE CONTROL See FigCLEAN-OUT USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR CHECK ENGINE OIL LEVEL See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGV-BELTS AUGER GEAR CASE1. Be sure throttle is in STOP position 2. Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig OTHER STORAGETO REMOVE WHEELS See Fig CARBURETORLoss of power TROUBLESHOOTINGDoes not start Engine idles orLIMITED WARRANTY
Top Page Image Contents