Simplicity 3190E, 3190M Safe Handling of Gasoline, Maintenance and Storage

Page 3

IMPORTANT SAFETY INSTRUCTIONS

OPERATIONAL PRECAUTIONS

8.Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting the machine to work.

9.After striking a foreign object, STOP the engine (motor), remove the key, and remove the wire from spark plug. Thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

10.STOP the engine if the machine starts to vibrate excessively as this normally indicates mechanical problems. Remove the key and disconnect the spark plug wire to prevent unintentional starting before servicing or repairing the machine.

11.DO NOT clear snow across the face of slopes. Exercise extreme CAUTION when changing direction on slopes. DO NOT attempt to clear steep slopes.

12.DO NOT leave machine unattended with the engine running. STOP engine and remove key to prevent unauthorized operation.

13.Release clutch control and make sure auger/impeller has STOPPED before rotating discharge chute, adjusting deflector, or placing hands near auger/impeller.

14.DO NOT use snow thrower on surfaces above ground level, such as, a roof of a building.

15.Exercise extreme CAUTION when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

16.DO NOT overload the machine capacity by attempting to clear snow at too fast a rate.

17.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

18.Disengage power to the auger/impeller when snow thrower is transported or not in use.

19.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, cabs and the like).

20.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive

1.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

2.Use only an approved fuel container.

3.DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool before refueling.

4.DO NOT refuel the machine indoors.

5.DO NOT store the machine or fuel container inside where there is an open flame, spark or pilot light such as on a water heater or other appliances.

6.DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling.

7.Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container, rather than a gasoline dispenser nozzle.

8.DO NOT start gas powered equipment in enclosed vehicles or trailers.

9.Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. DO NOT use a nozzle lock-open device

10.If fuel is spilled on clothing, change clothing immediately.

11.Never overfill a fuel tank. Replace fuel cap and tighten securely.

MAINTENANCE AND STORAGE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark, or pilot light as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2.Keep machine and engine free of excess oil, grease and spilled fuel to reduce fire hazard.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Inspect all bolts, nuts and screws frequently and keep properly tightened.

5.Use only recommended shear bolts (if equipped) to prevent possible damage to machine.

6.Service engine and make adjustments only when engine is stopped. Remove key, remove wire from spark plug, secure wire away from plug, and disconnect cord from electric starting motors to prevent accidental starting.

7.DO NOT change engine governor speed settings or overspeed engine.

8.DO NOT test for spark by grounding the spark plug next to spark plug hole. Spark from the plug could ignite gas exiting engine.

9.Have machine serviced by an authorized dealer at least once a year and have the dealer install any new safety devices.

10.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

Image 3
Contents Engine HP Engine Options Auger Width Series Designation Model Number ExplanationOperational Precautions Protection for ChildrenPreparation Safe Handling of Gasoline Maintenance and StorageTable of Contents Gasoline Cycle OIL PRE-START Check ListMinimum Gauge for Cord Sets Engaging Auger Move choke control to the choke on position. See FigureStopping Operating Instructions Check Auger Flite Shoe Service After First 5 Hours Check Auger Drive BeltStorage Procedure IntroductionAuger Belt Idler Pulley Adjustment Auger Belt Cable AdjustmentFrom Previous Auger Belt ReplacementRepair & Adjustments USE HRS Season Problem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT PartsDisclaimer of Warranty Year Limited WarrantyInstruction No -1806 I.R /6/03