Simplicity 1694242, 1694439, 1693985, 1693984, 1694435 Operation, Checks Before Each START-UP

Page 16

Operation

GENERAL OPERATION

CHECKS BEFORE EACH START-UP

1.Make sure all safety guards are in place and all nuts, bolts and clips are secure.

2.Check the engine oil level. See your engine Owner’s Manual for procedure and specifications.

3.Check to make sure spark plug wire is attached and spark plug is tightened securely. If necessary, torque spark plug to 15 ft. lbs.

4.Check the fuel level. Add fuel until the fuel level is no closer than 1/2 from the top of the tank to provide space for expansion. See your engine owner’s manu- al for fuel recommendations.

5.Check the scraper bar to make sure it is set at the desired height. Adjust the skid shoes if necessary.

6.Check the drive control (B, Figure 2), and auger con- trol (C, Figure 6) for proper operation. If adjustment is required, see the Adjustments Section for proce- dures.

7.Check the chute direction control (D, Figure 2) for proper operation. The discharge chute should rotate freely in both directions. See the Adjustments Section for adjustment procedures and troubleshooting.

8.Check the chute deflector (E, Figure 3) for proper operation. The deflector should pivot freely up and down when the chute deflector knob is loosened. If adjustment is required, see the Adjustments Section for procedures.

9.Position the chute at the desired starting direction and set the deflector at the desired angle.

10.Check the speed selector (A, Figure 2) for smooth operation. The control must move freely into each speed position gate and remain in position when released. If the speed selector does not move freely into all forward and reverse speed positions, contact your local authorized dealer for assistance.

WARNING

This unit is a “two-stage” snowthrower.

The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur.

To avoid injury, keep others and yourself away from the auger and the discharge chute whenever the engine is running. Read and follow all of the safety rules and warnings in this manual.

WARNING

To avoid serious injury, do not put your hands into the auger housing or discharge chute. If auger stalls or chute becomes plugged, use the following procedure to remove objects or clear the chute:

1.Release both the Drive and Auger Control levers.

2.Shut off the engine.

3.Remove the Engine Key.

4.Wait for moving parts to stop.

5.Disconnect spark plug wire.

6.Use a narrow board to remove foreign objects and clear the chute or auger. Never put your hands into the auger or discharge chute.

WARNING

For your safety, operation on slopes should be in an up and down direction only. If it becomes necessary to move across the face of a slope, use caution and do not blow snow. Be very careful when changing direction on a slope.

Proper winter footwear is recommended for the operator to help prevent slipping. Never attempt to clean snow from excessively steep slopes. The maximum slope for any operation is 17.7% (10º).

WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is hot or running. Always move outdoors to fill the tank. Keep snowthrower and gasoline away from open flame or spark.

12

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Print Vendor Instructions Operator’s ManualsPage OPERATOR’S Manual Series Large Frame SnowthrowerPage Table of Contents Safety Rules & Information General OperationSlope Operation Do NotSafety Rules Service and MaintenanceChildren EmissionsMaintenance and Storage Ansi B71.3-1995 WarningsTraining PreparationIdentification Tags Identification TagsCE Identification TAG Markings Safety Decals GeneralNorth American Model Decals CE Model DecalsSafety Icons Features, Controls, & Operation ALL Models Tecumseh ModelsFeatures & Controls Control LocationsEngine Controls Starting ControlsUnits with Optional Electric Start Manual StartGround Speed Controls Auger ControlDeflector Controls Scraper HeightOperation Checks Before Each START-UPStarting the Engine Ground Speed Selector Operating the SnowthrowerEngine Speed Deflector Scraper BAR & Skid ShoesFREE-WHEELING Traction Drive Lock After Each USEKlik-Pin Outer Hole Klik-Pin Inner HoleMaintenance ScheduleChecking Tire Pressure Check Auger Gear Case LubricationMaintenance LubricationImportant Note Hex ShaftStorage Check / Lubricate FREE-HAND LinkageLong Term Storage Longer than 30 Days Starting After Long Term StorageTroubleshooting Problem Possible Cause RemedyEngine fails to start Engine starts hard or runs poorlyScraper bar does not clean hard Auger does not stop when augerAuger rotates, but snow is not Thrown far enoughAdjustments Traction Drive System AdjustmentSpeed Selector Pivot Adjustment Traction Drive Clutch Rod & Spring AdjustmentAuger Drive System Adjustments Auger Drive Clutch Rod AdjustmentDischarge Chute Pinion Adjustment AdjustmentDischarge Chute Gear Bracket Adjustment Service Belt ReplacementShear PIN Replacement Shear PinsSpecifications DimensionsEngine ChassisMaintenance Items Replacement PartsTechnical Manuals

1694439, 1694435, 1693985, 1694242, 1693984 specifications

Simplicity 1693984, 1694242, 1693985, 1694435, and 1694439 represent a series of innovative solutions in the realm of technology, showcasing an impressive array of features aimed at enhancing user experience and streamlining functionalities. Designed with versatility in mind, these models cater to various applications, ensuring that they meet the diverse needs of users across different sectors.

One of the standout features of these models is their advanced connectivity options. Each model utilizes the latest wireless communication technologies, enabling seamless integration with other smart devices. This includes support for Bluetooth Low Energy (BLE) and Zigbee, facilitating efficient communication in IoT ecosystems. The integrated features allow for a more connected environment, whether in smart homes, industrial automation, or healthcare applications.

In terms of processing power, Simplicity’s models incorporate high-performance microcontrollers that not only enhance speed but also optimize energy consumption. This efficient power management is critical for long-lasting device operation, particularly in battery-powered applications. With low quiescent current and sleep modes, these models extend battery life, making them a preferred choice for portable devices.

The user interface experience is also prioritized in these models, with intuitive designs that allow easy navigation and user interaction. Touch-sensitive controls, combined with visually appealing displays, ensure that users can engage with the technology comfortably. This focus on user experience is complemented by a suite of customizable options, enabling users to tailor functionalities according to their specific needs.

Security is another critical characteristic of the Simplicity series. Each model integrates robust security protocols, ensuring data integrity and protecting sensitive information in connected applications. This is particularly significant in sectors like healthcare and finance, where data breaches can have serious implications.

Finally, the modularity of the Simplicity 1693984, 1694242, 1693985, 1694435, and 1694439 makes them highly adaptable across various industries. With a range of add-on functionalities and scalability options, these devices can evolve with technological advancements and changing user requirements.

In summary, the Simplicity series encapsulates modern technological trends, marrying advanced connectivity, processing prowess, user-oriented designs, and stringent security measures to meet the demands of today’s diverse applications.
Top Page Image Contents