MTD 614E To Stop Engine, To Engage Drive, To Engage Augers, Recoil Starter, Auger Control Test

Page 13

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

•If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before using the electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

•Connect power cord to switch box on engine. Plug the other end of power cord into a three-prong 120- volt, grounded, AC receptacle.

•Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.

•Push primer button two or three times for cold engine start, making sure to cover vent hole in primer button when pushing. DO NOT use primer to restart a warm engine after a short shutdown.

•Push starter button to start engine.

•When engine starts, release starter button and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF.

•When disconnecting the power cord, always unplug from the three-prong receptacle first and then from the snow thrower.

Recoil Starter

•Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.

•Push primer button two or three times for cold engine start. DO NOT use primer to restart a warm engine after a short shutdown.

NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15 degrees Fahrenheit.

•Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.

•Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.

•As engine warms up and begins to operate evenly, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position.

To Stop Engine

•Run engine for a few minutes before stopping to help dry off any moisture on the engine.

•To help prevent possible freeze-up of starter, proceed as follows:

Electric Starter (If equipped)

•Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.

Recoil Starter

•With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to engine or starter.

•To stop engine, move throttle control to “stop” or “off” position.

•Remove the ignition key. Do not turn key.

•Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

NOTE: Do not lose ignition key. Keep it in a safe place. Engine will not start without the ignition key.

•Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

To Engage Drive

•With the engine running near top speed, move shift lever into one of the five FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use the slower speeds until you are familiar with the operation of the snow thrower.

•Squeeze the auger control grip and the augers will turn. Release it and the augers will stop.

•Squeeze traction control grip and the snow thrower will move. Release it and drive motion will stop.

•NEVER move shift lever without releasing drive clutch.

To Engage Augers

•To engage the augers and start throwing snow, squeeze the auger control grip against the left handle. Release to stop the augers.

Auger Control Test

IMPORTANT: Perform the following test before operating your snow thrower for the first time and at the start of each winter season.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesMaintenance and Storage Contents of Hardware Pack Boxed Units Unpacking Assembling Your Snow ThrowerLoose Parts Boxed Unit CrateHardware Group A, B and E Attaching Handle AssemblyAttaching Shift Rod Hardware D Attaching Clutch Cables Attaching the Chute Assembly Hardware FAttaching The Chute Directional Control Shift Lever Know Your Snow ThrowerAuger Drive Control Traction ControlOperating Your Snow Thrower To Engage Drive To Stop EngineTo Engage Augers Recoil StarterDrift Cutters If Equipped Chute Clean-Out ToolOperating Tips Traction Control and Shift Lever Making AdjustmentsAdjusting Shift Rod Chute AssemblyAuger Control Skid ShoesDrive Wheels Maintaining Your Snow ThrowerLubrication Engine Servicing Your Snow ThrowerShave Plate and Skid Shoes Augers Belt Removal and ReplacementAuger Belts Off-Season Storage Friction Wheel RubberDrive Belt Trouble Possible Causes Corrective Action Trouble Shooting GuideModels 614E, 644E, & 664G Part Description Models 614E, 644E, & 664GModels 614E, 644E, & 664G Jam Lock Nut 3/8-24 Compression Spring 736-0105 Drive Clutch Cable Auger Clutch Wheels Models 614E, 644E, & 664G Models 614E 1615 Models 644E & 664GSize Page MANUFACTURER’S Limited Warranty for

614E specifications

The MTD 614E is a versatile and highly regarded lawn mower that caters to both residential and commercial gardening needs. Known for its blend of efficiency, durability, and ease of use, the MTD 614E is designed to make lawn care a breeze for users of all experience levels.

One of the main features of the MTD 614E is its powerful engine. Equipped with a robust and reliable 6.5 HP engine, it delivers ample power for tackling tough grass and uneven terrain. This engine is designed for fuel efficiency while providing sufficient torque for effective cutting and mulching. Users can count on performance that ensures clean cuts and a well-manicured lawn.

The cutting deck of the MTD 614E is another standout feature. The mower is fitted with a 14-inch cutting deck, allowing it to navigate tight spaces and flower beds with ease. The adjustable cutting height—typically ranging from 1 to 3 inches—enables users to customize their mowing to suit different grass types and seasonal conditions. This flexibility is crucial for achieving the desired lawn aesthetic and health.

Durability is a hallmark of the MTD 614E construction. Featuring a sturdy steel frame and high-quality components, this mower can withstand the rigors of regular use. The wheels are designed to offer excellent traction, which is essential for maintaining stability on slopes and uneven ground.

Technologically, the MTD 614E boasts a user-friendly recoil start system, simplifying the process of getting the mower up and running. Maintenance is also straightforward, with easily accessible engine oil and air filter compartments that facilitate routine checks and servicing.

Another notable characteristic of the MTD 614E is its lightweight design, making it easy to maneuver and transport. This is particularly beneficial for homeowners with smaller yards or those who need to move the mower frequently between locations. Additionally, the compact size allows for convenient storage in tight spaces.

The mower's ergonomic handle ensures comfort during operation, reducing strain on the user's hands and back. Overall, the MTD 614E effectively combines power, efficiency, and ease of use, making it a popular choice for individuals seeking an effective lawn care solution. Whether for a small garden or larger green spaces, the MTD 614E proves itself as a reliable partner in maintaining a beautiful lawn.
Top Page Image Contents