MTD 614E manual Attaching Handle Assembly, Hardware Group A, B and E

Page 7

•Remove the lower two plastic wing knobs, cupped washers and carriage bolt (eyebolt on the left side) from the lower handle. See Figure 3.

Eyebolt

Wing Knobs,

Washers

and Bolts

Figure 3

•Raise the upper handle assembly until it locks over the lower handle. See Figure 4.

•Observe the lower rear area of the snow thrower to be sure both cables are aligned with roller guides.

•Secure the upper handle and lower handle with the two plastic wing knobs, cupped washers and carriage bolt (eyebolt on the left side) previously removed. See Figure 4.

Hex

Hairpin Clip

Connector

Nut

 

Eyebolt

Wing Knobs

 

Figure 4

•Adjust the eyebolt on the chute directional control so the rod does not come into contact with the engine by moving the hex nut against the handle (if necessary). Retighten the wing nut to secure the directional control in this position.

•Slide the connector down over the end of the lower shift rod. See Figure 4. Tap the connector until it locks on the lower shift rod.

If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or change directions.

•Thread the jam nuts all the way up each of the “Z” fittings, toward the handle panel. See Figure 11.

•Make certain all cables are in the grooves of the cable roller guides located in the lower rear of the unit, one on each side. See Figure 9.

•Thread the coupling end of the cable onto the threaded portion of the “Z” fitting until the rubber bumper (located on the underside of the clutch lever) only lightly contacts the upper handle.

IMPORTANT: The cable should have very little slack, but should NOT be tight. An overtightened cable may prohibit the auger and drive from disengaging.

WARNING: Over-tightening the cable may prohibit the auger and drive from disengaging and compromise the safety of the snow thrower. Do NOT overtighten the cable.

•Once properly adjusted, tighten the jam nut against the coupling end of the cable to lock it in position.

Refer to Auger Control Test on page 13 prior to operating your snow thrower. Read and follow all instructions carefully and perform all adjustments to verify your snow thrower is operating safely and properly.

Assembly (Boxed Unit)

WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

Attaching Handle Assembly

(Hardware Group A, B and E)

•Attach left handle and left clutch bracket to handle panel with two carriage bolts, cupped washers and hex patch nuts. (Be sure the bend in the grip bracket is towards the center of the handle panel.) Do not tighten at this time. See Figure 5.

Handle Panel

 

Left Bracket

Carriage

 

Bolts

 

 

Hex

Left Handle

Patch Nuts

 

(Curves in)

 

Bell Washers

Figure 5

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesMaintenance and Storage Contents of Hardware Pack Boxed Units Crate Assembling Your Snow ThrowerUnpacking Loose Parts Boxed UnitHardware Group A, B and E Attaching Handle AssemblyAttaching Shift Rod Hardware D Attaching Clutch Cables Attaching the Chute Assembly Hardware FAttaching The Chute Directional Control Traction Control Know Your Snow ThrowerShift Lever Auger Drive ControlOperating Your Snow Thrower Recoil Starter To Stop EngineTo Engage Drive To Engage AugersDrift Cutters If Equipped Chute Clean-Out ToolOperating Tips Traction Control and Shift Lever Making AdjustmentsSkid Shoes Chute AssemblyAdjusting Shift Rod Auger ControlDrive Wheels Maintaining Your Snow ThrowerLubrication Engine Servicing Your Snow ThrowerShave Plate and Skid Shoes Augers Belt Removal and ReplacementAuger Belts Off-Season Storage Friction Wheel RubberDrive Belt Trouble Possible Causes Corrective Action Trouble Shooting GuideModels 614E, 644E, & 664G Part Description Models 614E, 644E, & 664GModels 614E, 644E, & 664G Jam Lock Nut 3/8-24 Compression Spring 736-0105 Drive Clutch Cable Auger Clutch Wheels Models 614E, 644E, & 664G Models 614E 1615 Models 644E & 664GSize Page MANUFACTURER’S Limited Warranty for

614E specifications

The MTD 614E is a versatile and highly regarded lawn mower that caters to both residential and commercial gardening needs. Known for its blend of efficiency, durability, and ease of use, the MTD 614E is designed to make lawn care a breeze for users of all experience levels.

One of the main features of the MTD 614E is its powerful engine. Equipped with a robust and reliable 6.5 HP engine, it delivers ample power for tackling tough grass and uneven terrain. This engine is designed for fuel efficiency while providing sufficient torque for effective cutting and mulching. Users can count on performance that ensures clean cuts and a well-manicured lawn.

The cutting deck of the MTD 614E is another standout feature. The mower is fitted with a 14-inch cutting deck, allowing it to navigate tight spaces and flower beds with ease. The adjustable cutting height—typically ranging from 1 to 3 inches—enables users to customize their mowing to suit different grass types and seasonal conditions. This flexibility is crucial for achieving the desired lawn aesthetic and health.

Durability is a hallmark of the MTD 614E construction. Featuring a sturdy steel frame and high-quality components, this mower can withstand the rigors of regular use. The wheels are designed to offer excellent traction, which is essential for maintaining stability on slopes and uneven ground.

Technologically, the MTD 614E boasts a user-friendly recoil start system, simplifying the process of getting the mower up and running. Maintenance is also straightforward, with easily accessible engine oil and air filter compartments that facilitate routine checks and servicing.

Another notable characteristic of the MTD 614E is its lightweight design, making it easy to maneuver and transport. This is particularly beneficial for homeowners with smaller yards or those who need to move the mower frequently between locations. Additionally, the compact size allows for convenient storage in tight spaces.

The mower's ergonomic handle ensures comfort during operation, reducing strain on the user's hands and back. Overall, the MTD 614E effectively combines power, efficiency, and ease of use, making it a popular choice for individuals seeking an effective lawn care solution. Whether for a small garden or larger green spaces, the MTD 614E proves itself as a reliable partner in maintaining a beautiful lawn.
Top Page Image Contents