MTD 614E manual Chute Assembly, Auger Control, Skid Shoes, Carburetor, Adjusting Shift Rod

Page 16

With the traction control is engaged, the friction wheel must contact the drive plate. See Figure 20.

Friction

Wheel

Gear Shaft

Drive

Plate

Gap

Figure 20

If adjustment is necessary:

Loosen the jam nut on the traction control cable and thread the cable in or out as necessary.

Retighten the jam nut to secure the cable when correct adjustment is reached.

Reassemble the frame cover.

NOTE: If you placed plastic under the gas cap earlier, remove it now.

Chute Assembly

The distance snow is thrown can be adjusted by changing the angle of the chute assembly. To do so, stop the engine by removing the ignition key and loosen the plastic wing knobs found on either side of the discharge chute. Pivot the chute upward or downward before re-tightening the wing knobs.

Auger Control

Refer to Auger Control Test in the Operating Section to adjust the auger control.

Skid Shoes

The space between the shave plate and the ground can be adjusted. See Figure 21.

For close snow removal on a smooth surface, raise skid shoes higher on the auger housing.

Use a middle or lower position when the area to be cleared is uneven.

Carriage

 

Bolts

Hex Nuts

 

 

Skid

 

Shoes

Figure 21

WARNING: Do not operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing injury to the operator and/or damage to the snow thrower.

Adjust skid shoes by loosening the four hex nuts and carriage bolts. Move skid shoes to desired position.

Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes. Retighten nuts and bolts securely.

Carburetor

Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude and load.

Refer to the separate engine manual, packed with your unit, for carburetor adjustment information.

WARNING: If any adjustments need to be made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of muffler, engine and other surrounding heated surfaces.

Adjusting Shift Rod

Remove the hairpin clip and flat washer from the ferrule and remove the ferrule from the shift lever. Place the shift lever in the fastest forward speed position.

Push down on the shift arm assembly as far as it will go. Thread the ferrule up or down the shift rod and align it with the hole closest to the shift knob on the narrow side of the shift lever assembly behind the handle panel. Refer to Figure 10.

16

Image 16
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance and Storage Contents of Hardware Pack Boxed Units Assembling Your Snow Thrower UnpackingLoose Parts Boxed Unit CrateAttaching Handle Assembly Hardware Group A, B and EAttaching Shift Rod Hardware D Attaching the Chute Assembly Hardware F Attaching Clutch CablesAttaching The Chute Directional Control Know Your Snow Thrower Shift LeverAuger Drive Control Traction ControlOperating Your Snow Thrower To Stop Engine To Engage DriveTo Engage Augers Recoil StarterDrift Cutters If Equipped Chute Clean-Out ToolOperating Tips Making Adjustments Traction Control and Shift LeverChute Assembly Adjusting Shift RodAuger Control Skid ShoesDrive Wheels Maintaining Your Snow ThrowerLubrication Engine Servicing Your Snow ThrowerShave Plate and Skid Shoes Augers Belt Removal and ReplacementAuger Belts Off-Season Storage Friction Wheel RubberDrive Belt Trouble Shooting Guide Trouble Possible Causes Corrective ActionModels 614E, 644E, & 664G Models 614E, 644E, & 664G Part DescriptionModels 614E, 644E, & 664G Jam Lock Nut 3/8-24 Compression Spring 736-0105 Drive Clutch Cable Auger Clutch Wheels Models 614E, 644E, & 664G Models 614E Models 644E & 664G 1615Size Page MANUFACTURER’S Limited Warranty for

614E specifications

The MTD 614E is a versatile and highly regarded lawn mower that caters to both residential and commercial gardening needs. Known for its blend of efficiency, durability, and ease of use, the MTD 614E is designed to make lawn care a breeze for users of all experience levels.

One of the main features of the MTD 614E is its powerful engine. Equipped with a robust and reliable 6.5 HP engine, it delivers ample power for tackling tough grass and uneven terrain. This engine is designed for fuel efficiency while providing sufficient torque for effective cutting and mulching. Users can count on performance that ensures clean cuts and a well-manicured lawn.

The cutting deck of the MTD 614E is another standout feature. The mower is fitted with a 14-inch cutting deck, allowing it to navigate tight spaces and flower beds with ease. The adjustable cutting height—typically ranging from 1 to 3 inches—enables users to customize their mowing to suit different grass types and seasonal conditions. This flexibility is crucial for achieving the desired lawn aesthetic and health.

Durability is a hallmark of the MTD 614E construction. Featuring a sturdy steel frame and high-quality components, this mower can withstand the rigors of regular use. The wheels are designed to offer excellent traction, which is essential for maintaining stability on slopes and uneven ground.

Technologically, the MTD 614E boasts a user-friendly recoil start system, simplifying the process of getting the mower up and running. Maintenance is also straightforward, with easily accessible engine oil and air filter compartments that facilitate routine checks and servicing.

Another notable characteristic of the MTD 614E is its lightweight design, making it easy to maneuver and transport. This is particularly beneficial for homeowners with smaller yards or those who need to move the mower frequently between locations. Additionally, the compact size allows for convenient storage in tight spaces.

The mower's ergonomic handle ensures comfort during operation, reducing strain on the user's hands and back. Overall, the MTD 614E effectively combines power, efficiency, and ease of use, making it a popular choice for individuals seeking an effective lawn care solution. Whether for a small garden or larger green spaces, the MTD 614E proves itself as a reliable partner in maintaining a beautiful lawn.