Snapper 555M, 555M, 15225, E15225, 18245E, E18245, 860E, 860M manual Operating the Snowthrower

Page 15

Operation

OPERATING THE SNOWTHROWER

1.Rotate the discharge chute to the desired direction.

2.Set the speed selector to the desired forward speed.

3.Fully press and hold the auger control (C, Figure 7) on the right-hand grip to begin auger rotation. To dis- engage the auger, completely release the lever.

4.Fully press and hold the traction drive control lever (B, Figure 7) on the left-hand grip to engage the trac- tion drive and begin moving the snowthrower. To dis- engage the traction drive, completely release the lever. If engaged at the same time, the drive control

(B)will lock the auger control (C) in the engaged

position. Releasing the drive control (B) will release the auger control (C).

5.Select forward or reverse speeds as needed using the speed selector (A, Figure 7). Release the drive control lever whenever changing drive speeds.

NOTE: After 5 - 10 hours of use, it may be necessary to adjust the tension on the traction drive cable. See "Traction Drive Clutch Cable Adjustment" in the Service Section for the adjustment procedure.

CLEARING A CLOGGED DISCHARGE CHUTE

Hand contact with the rotating auger/impeller inside the discharge chute is the most common cause of injury associated with snowthrowers. DO NOT use your hand to clean out the discharge chute. To clear the chute:

1.Stop the engine. Remove the key.

2.Wait 10 seconds to be sure the auger/impeller blades have stopped rotating.

3.Always use the clean-out tool. DO NOT use your hands.

GROUND SPEED SELECTOR

Use the speed selector (A, Figure 7) to control the drive speed of the snowthrower. There are five forward speeds and two reverse speeds.

Use the lower speeds to blow deep or wet snow. Use the higher speeds to blow light snow or to drive the snow- thrower without blowing snow.

To change speeds, first release the traction drive control lever (B, Figure 7), then move the speed selector to the desired speed setting. Fully press the traction drive con- trol lever to resume operation.

ENGINE SPEED

Run the engine at full throttle when operating. Use the engine throttle lever (See Figure 8) to set the engine speed. Slide the throttle lever UP to increase engine speed, and DOWN to reduce speed.

C

A

D

B

 

Figure 7. Operator's Control Position

A.

Speed Selector

C.

Auger Control

B.

Drive Control

D.

Chute Direction Control

Throttle

Lever

Throttle

Lever

Figure 8. Engine Speed Selection

14

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models OPERATOR’S ManualTable of Contents Safety Rules & Information Children Safety RulesPage CE Models Identification NumbersCE Identification TAG Markings North AmericanCE Model Decals Safety DecalsGeneral North American Model DecalsCE Safety Icons & Compliance Specs ALL Models Tecumseh Models Briggs & Stratton Models Features, Controls, & OperationControl Locations Features & ControlsManual Start Engine ControlsStarting Controls Units with Optional Electric StartScraper Height Ground Speed ControlsAuger Control Deflector ControlsChecks Before Each START-UP OperationStarting the Engine Engine Speed Operating the SnowthrowerClearing a Clogged Discharge Chute Ground Speed SelectorScraper BAR & Skid Shoes DeflectorAfter Each USE FREE-WHEELING Traction Drive LockMaintenance Schedule Checking Tire PressureCheck Auger Gear Case Lubrication Lubrication MaintenanceStorage Lubricating the Auger Shaft & AssemblyStorage Lubrication Check / Lubricate FREE-HAND LinkageTroubleshooting Troubleshooting, Adjustment, & ServiceTroubleshooting Run-In Adjustment AdjustmentsTraction Drive Clutch Cable Adjustment Initial AdjustmentPinion Gear Adjustment Manual Discharge Chute Control Linkage AdjustmentDrive Belt Adjustment Auger Drive Clutch Cable AdjustmentAdjusting Auger Drive Belt Checking Auger Belt & Belt Guide AdjustmentsTraction Drive Belt Replacement Adjustments & ServiceDrive Belt Replacement Adjusting Auger Belt GuideAuger Drive Belt Replacement ServiceShear PIN Replacement Roller Chain ReplacementHP* Tecumseh DimensionsEngine ChassisReplacement Parts Maintenance ItemsTechnical Manuals

555, 555M, 555M, 15225, E15225, 18245E, E18245, 860E, 860M specifications

Snapper's range of products, including the Snapper 555, 555M, 55555M, 15225, E15225, 18245E, E18245, 860E, and 860M, showcases advanced engineering and innovative design in the realm of outdoor power equipment. These models cater to homeowners and professionals alike, delivering reliable performance and versatile functionality for various landscaping tasks.

One of the hallmark features of the Snapper 555 series is its robust build quality. These mowers are engineered with durable materials, ensuring longevity even under extensive use. They are designed to handle various terrain types, providing users with the confidence to tackle challenging landscapes. The 555M and 55555M variants include additional power enhancements that cater to larger properties, optimizing cutting efficiency with their powerful engines.

The Snapper 15225 and E15225 models are particularly notable for their lightweight design, which facilitates maneuverability in tight spaces. These models excel in residential lawns, featuring a compact body without sacrificing cutting performance. The electric version, E15225, offers an eco-friendly alternative, operating quietly and producing zero emissions, making it perfect for environmentally conscious homeowners.

In contrast, the Snapper 18245E and E18245 models are built for more extensive lawn care. They incorporate larger cutting decks and advanced blade technologies, ensuring a clean and even cut. The ergonomic design of these mowers provides enhanced comfort, reducing operator fatigue during longer mowing sessions.

The Snapper 860E and 860M models are engineered to deliver high performance in commercial applications. These powerful machines are equipped with advanced engine technology that maximizes fuel efficiency while providing ample power for tough mowing jobs. Their heavy-duty construction allows them to withstand the rigors of professional use, making them a valuable asset for landscapers and lawn care services.

Overall, the Snapper lineup embodies a commitment to quality, efficiency, and user-friendly designs. Each model incorporates unique features and cutting technologies tailored for specific user needs, whether it be residential mowing or professional landscaping. With their reputation for reliability and performance, Snapper's mowers continue to be a preferred choice for those seeking high-quality outdoor power equipment.
Top Page Image Contents