Poulan 415136 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always remove safety igni- tion key and disconnect spark plug wire. Place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles 178899 17000616Repair Parts Snow Thrower - Model NO. PR5524ES Drive Repair Parts Snow Thrower - Model NO. PR5524ES Drive Page 416717X004 KEY Part Description17490408 413429X479Page 181037 Decal, Danger Limited Warranty

415136 specifications

The Poulan 415136 is a powerful and versatile chainsaw designed for both professional loggers and homeowners alike. Its robust design and advanced technology make it suitable for various cutting tasks, from felling trees to pruning and firewood preparation. With a focus on reliability and performance, the Poulan 415136 stands out in the competitive chainsaw market.

One of the key features of the Poulan 415136 is its powerful engine. Equipped with a high-performance gas engine, it offers impressive cutting speed and efficiency. The engine's reliability ensures that users can rely on it for extended periods without worrying about performance degradation. Its 40cc displacement provides a perfect balance between power and weight, making it easy to maneuver during operation.

The Poulan 415136 also features an automatic lubrication system that ensures the chain and bar remain well-lubricated during use. This technology not only extends the life of the chain and bar but also helps maintain consistent cutting performance. The adjustable oil flow allows users to customize the lubrication according to their specific cutting needs, making the chainsaw versatile for various tasks.

Another standout characteristic is its ergonomic design. The chainsaw is equipped with a comfortable handle that minimizes user fatigue, allowing for longer hours of usage without discomfort. The anti-vibration system further enhances the experience by reducing vibrations transmitted to the user, promoting smoother operation during cutting.

Safety is a crucial consideration for any chainsaw, and the Poulan 415136 does not disappoint. It features a chain brake that stops the chain almost immediately in case of kickback, protecting the user from potential accidents. Additionally, the chainsaw's safety latch prevents accidental starting, adding an extra layer of security during operation.

The Poulan 415136 is also designed for easy maintenance. Its tool-less chain tensioning system allows users to easily adjust the chain tension without the need for additional tools, saving time and effort during operation. This feature is particularly beneficial for users who require quick adjustments on the job site.

In summary, the Poulan 415136 is an outstanding chainsaw that combines power, efficiency, and user-friendly features. With its high-performance engine, automatic lubrication system, ergonomic design, and enhanced safety features, it is ideal for both professional users and homeowners looking to tackle their cutting tasks efficiently. Whether you are clearing fallen trees or maintaining your property, the Poulan 415136 is a reliable choice that delivers exceptional performance.
Top Page Image Contents