Poulan 415136 owner manual To Remove Wheels See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler

arm bracket while bringing snow thrower together),

 

separate the snow thrower and repeat step 10. Belt

 

must be fully seated in pulley groove when bringing

16

the snow thrower together.

12.Install the two (2) hex boltsand tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

CLUTCHING

 

IDLER ARM

 

BRACKET

 

 

AUGER PULLEY

 

 

 

BOLT

FRAME

AUGER

 

HOUSING

 

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDischarge chute control lever used to change the di HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Scraper BARCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles 178899 17000616Repair Parts Snow Thrower - Model NO. PR5524ES Drive Repair Parts Snow Thrower - Model NO. PR5524ES Drive Page KEY Part Description 17490408416717X004 413429X479Page 181037 Decal, Danger Limited Warranty

415136 specifications

The Poulan 415136 is a powerful and versatile chainsaw designed for both professional loggers and homeowners alike. Its robust design and advanced technology make it suitable for various cutting tasks, from felling trees to pruning and firewood preparation. With a focus on reliability and performance, the Poulan 415136 stands out in the competitive chainsaw market.

One of the key features of the Poulan 415136 is its powerful engine. Equipped with a high-performance gas engine, it offers impressive cutting speed and efficiency. The engine's reliability ensures that users can rely on it for extended periods without worrying about performance degradation. Its 40cc displacement provides a perfect balance between power and weight, making it easy to maneuver during operation.

The Poulan 415136 also features an automatic lubrication system that ensures the chain and bar remain well-lubricated during use. This technology not only extends the life of the chain and bar but also helps maintain consistent cutting performance. The adjustable oil flow allows users to customize the lubrication according to their specific cutting needs, making the chainsaw versatile for various tasks.

Another standout characteristic is its ergonomic design. The chainsaw is equipped with a comfortable handle that minimizes user fatigue, allowing for longer hours of usage without discomfort. The anti-vibration system further enhances the experience by reducing vibrations transmitted to the user, promoting smoother operation during cutting.

Safety is a crucial consideration for any chainsaw, and the Poulan 415136 does not disappoint. It features a chain brake that stops the chain almost immediately in case of kickback, protecting the user from potential accidents. Additionally, the chainsaw's safety latch prevents accidental starting, adding an extra layer of security during operation.

The Poulan 415136 is also designed for easy maintenance. Its tool-less chain tensioning system allows users to easily adjust the chain tension without the need for additional tools, saving time and effort during operation. This feature is particularly beneficial for users who require quick adjustments on the job site.

In summary, the Poulan 415136 is an outstanding chainsaw that combines power, efficiency, and user-friendly features. With its high-performance engine, automatic lubrication system, ergonomic design, and enhanced safety features, it is ideal for both professional users and homeowners looking to tackle their cutting tasks efficiently. Whether you are clearing fallen trees or maintaining your property, the Poulan 415136 is a reliable choice that delivers exceptional performance.
Top Page Image Contents