Poulan 414641 owner manual To Throw Snow See Fig, Using the CLEAN-OUT Tool See Fig

Page 10

OPERATION

HIGH POSITION

KNOB

CHUTE

DEFLECTOR

LOW POSITION

FIG. 13

TO THROW SNOW (See Fig. 14)

The auger rotation is controlled by the auger control lever located on the right side handle.

Squeeze auger control lever to handle to engage the auger and throw snow.

Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 14

USING THE CLEAN-OUT TOOL (See Fig. 15)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac- cidental starting.

Release the auger control lever and shut off the engine.

Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are in the directionof discharge) before restarting theengine.

Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous-

ing and the discharge chute.

10

DISCHARGE CHUTE

CLEAN-OUT

TOOL

MOUNTING CLIP

FIG. 15

TO MOVE FORWARD AND BACKWARD (See Fig. 16)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

Squeeze traction drive control lever to handle to engage the drive system.

Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 16

Image 10
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower TractionRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDischarge chute control lever used to change the di HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 205 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PP8527ES Handles Repair Parts Snow Thrower - Model NO. PP8527ES Handles Repair Parts Snow Thrower - Model NO. PP8527ES Drive Repair Parts Snow Thrower - Model NO. PP8527ES Drive 07Chassis-chain-cord-Tec2 KEY Part Description Page KEY Part Description Limited Warranty