Poulan 414641 owner manual KEY Part Description

Page 21

REPAIR PARTS SNOW THROWER - - MODEL NO. PP8527ES (96192001700)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

PART

 

NO.

NO.

DESCRIPTION

4

191079

Pulley, Impeller

5

188909

Bearing Assembly, Flange

6

155377

Nut, Hex Flange 5/16-18

7180355 Bolt, Flat Head, Carriage 5/16-18 x 5/8

872270505 Bolt, Carriage 5/16-18 x 5/8

9163183 Nut, Cage 3/8-16

10404929X428 Housing, Auger

11404932X428 Bar, Scraper

12178675X008 Bracket, Corner Discharge

13175322 Base, Discharge Chute

14

19111507

Washer, Flat

15

10040500

Washer, Lock 5/16

16

74940516

Screw, Hex Head 5/16-18 x 3/4

17

405637

Grease Fitting

18179582 Screw, Hex Head 5/16 x 1

1973800400 Nut, Hex Lock 1/4-20

20155377 Nut, Hex Lock 5/16-18

22178777X479 Skid Plate, RH

25

72270506

Bolt, Carriage 5/16-18 x 3/4

26

174658

Bearing, Auger

27

174697

Washer, Thrust, 1"

28

198636

Bolt, Shear

29

174762X479

Skid Plate, LH

30405977X421 Auger Assembly, RH

31405976X421 Auger Assembly, LH

32

407768

O-Ring

33

407769

Bushing, Flange 3/4

34

174681

Washer, Thrust 3/4

35

174684

Bearing, Thrust 3/4

36

407757

Shaft, Impeller

37

174683

Washer, Thrust 5/8

38

407758

Bushing, Flange 5/8

39

407767

Screw, Hex Washer Head 5/16-18 x 3/4

40

407760

Plug, Case

41

407761

Housing, Gearbox, RH

42

407770

Seal, Oil

43

407762

Bushing, Flange, 1"

44

189282

Key, Square 1/4 x 1/4 x 7/8

45

407763

Gear, Worm

46

407764

Shaft, Auger

47

407765

Housing, Gearbox, LH

48175321X479 Impeller Assembly

4974780426 Screw, Hex Head 1/4-20 x 1-5/8

50407766 Gasket, Gearbox

517836M Pin, Roll 3/16 x 1-1/8

55

198638

Spacer

56

180684

Multi-Wrench

57

196710

Gearbox Assembly

58

411939

Plug Bearing Hole

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

Image 21
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for startingDischarge chute control lever used to change the di Stopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other StorageTroubleshooting Service Notes AIG plugr1 KEY Part Description 205 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PP8527ES Handles Repair Parts Snow Thrower - Model NO. PP8527ES Handles Repair Parts Snow Thrower - Model NO. PP8527ES Drive Repair Parts Snow Thrower - Model NO. PP8527ES Drive 07Chassis-chain-cord-Tec2 KEY Part Description Page KEY Part Description Limited Warranty