Poulan 415242 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Storage Other TroubleshootingRepair Parts 405985X479 405986X479205 414280 Knob, Lever Handles Repair Parts Repair Parts Drive Repair Parts Page KEY Part Description 416954417014X428 Wheels / Decals KEY Part Description Limited Warranty

415242 specifications

The Poulan 415242 is a versatile and powerful chainsaw designed for both casual users and experienced professionals. Known for its reliability and cutting performance, this chainsaw has become a popular choice among homeowners and small landowners who require efficient tools for yard maintenance and light to medium-duty tasks.

At the heart of the Poulan 415242 is its robust engine. The chainsaw features a 42cc two-stroke engine that delivers a considerable amount of power for tackling various cutting jobs. With a maximum speed of around 8,500 RPM, users can expect efficient performance whether they're trimming branches, felling trees, or cutting firewood. The engine's design allows for easy starts, thanks to the inclusion of a simplified starting system that reduces the number of pulls needed to ignite the engine.

One of the standout features of the Poulan 415242 is its low-vibration technology. This feature significantly reduces the amount of vibrations transferred to the operator, resulting in a more comfortable cutting experience, especially during extended use. Coupled with an ergonomic handle design, users can maintain a secure grip without experiencing excessive fatigue.

Safety is a critical aspect of chainsaw operation, and the Poulan 415242 incorporates several safety features. It includes a chain brake that automatically engages to stop the chain in the event of kickback, providing an added layer of protection to the user. Additionally, the chainsaw comes equipped with a throttle lockout, preventing accidental acceleration during operation.

Another innovative characteristic of the Poulan 415242 is its easy-access air filter and tool-less chain adjustment system. The accessible air filter simplifies maintenance, ensuring the chainsaw remains in optimal condition for performance. The tool-less chain adjustment allows users to quickly and easily adjust the chain tension as needed, promoting efficiency and productivity.

The Poulan 415242 is equipped with a 16-inch guide bar, making it suitable for a range of cutting applications. The size strikes an excellent balance between maneuverability and cutting power, allowing users to navigate tight spaces while efficiently handling larger logs.

With its combination of power, safety, and user-friendly features, the Poulan 415242 stands out as a reliable and effective tool for those in need of a dependable chainsaw. Whether for trimming, pruning, or felling, this chainsaw provides the performance and comfort needed for a variety of tasks. Users can tackle their projects with confidence, knowing they have a quality tool at their side.
Top Page Image Contents