To Remove Wheels See Fig | Poulan 199350 instruction

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME	AUGER
ASSEMBLY	HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from ﬁre or ﬂame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and ﬂat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing

the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install ﬂat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

	BELT KEEPER
	TRACTION DRIVE BELT
	ENGINE	FLAT WASHER
	PULLEY	FLAT WASHER
	PULLEY
		LOCKWASHER
		BOLT
IDLER ARM			AUGER
SQUARE			BELT
HOLE
CLUTCHING
IDLER ARM
BRACKET
	AUGER PULLEY
		BOLT	LOCK
			WASHER
FRAME	AUGER
FRAME	HOUSING

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 22

199350 specifications

The Poulan 199350 is a remarkable chainsaw designed for both amateur enthusiasts and professional users who require reliability and power for various cutting tasks. This model is known for its robust performance, making it a popular choice for homeowners and professionals alike.

One of the key features of the Poulan 199350 is its potent 50cc gas engine, which delivers impressive cutting power. This engine is engineered to provide high torque, allowing it to easily cut through thick branches and even small trees. The balanced design of the chainsaw ensures that users can maneuver it effortlessly, reducing fatigue during extended use.

A standout characteristic of the Poulan 199350 is its efficient air filtration system. This innovative feature helps to prolong the life of the engine by keeping dirt and debris from entering critical components. The air filter is easy to access and clean, which is vital for maintaining optimal performance and reliability over time.

In terms of safety, the Poulan 199350 is equipped with a chain brake system that provides an added layer of protection against kickback. This safety feature ensures that the chain stops quickly in the event of unexpected movement, giving users peace of mind while operating the saw. Additionally, the chainsaw has a low kickback chain that further minimizes the chances of accidents.

The Poulan 199350 also boasts an automatic oiler that maintains the chain's lubrication, which is crucial for smooth operation and reduced wear. This convenience allows users to focus on their cutting tasks without the hassle of manual lubrication.

Another significant advantage of the Poulan 199350 is its lightweight design, which enhances portability and ease of use. Weighing around 12 pounds, this chainsaw is easy to transport and handle, making it suitable for a variety of outdoor projects, from trimming and pruning to felling small trees.

Moreover, its tool-less chain tensioning feature allows for quick adjustments, ensuring that the chain remains at the ideal tension at all times. This attribute is particularly beneficial for users who require quick setup and operation while on the job.

In conclusion, the Poulan 199350 stands out in the chainsaw market due to its powerful engine, advanced safety features, efficient air filtration, and user-friendly design. Whether for home maintenance or professional landscaping, this chainsaw delivers exceptional performance and reliability, making it an excellent investment for anyone in need of a quality cutting tool.