Poulan 414741 To Remove Wheels See Fig, Remove the klik pin and remove wheel from axle

Page 17

SERVICE AND ADJUSTMENTS

be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistantstand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and remove clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 24

TO REMOVE WHEELS (See Fig. 25)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

17 dealer. Tire sealant also prevents tire dry rot and corrosion.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See FigScraper BAR Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting 2220 KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP11530ES Handles Repair Parts Snow Thrower Model PP11530ES Handles Repair Parts Drive Repair Parts Snow Thrower Model PP11530ES Drive Page 417014X428 KEY Part DescriptionRepair Parts Snow Thrower Model PP11530ES Wheels / Decals Repair Parts Limited Warranty

414741 specifications

The Poulan 414741 is a versatile and powerful chainsaw designed to meet the needs of both seasoned professionals and occasional users. With a blend of innovation, durability, and user-friendly features, this model stands out in the competitive market of handheld power tools.

One of the defining characteristics of the Poulan 414741 is its robust engine. Equipped with a reliable 40cc two-stroke engine, this chainsaw delivers impressive power that allows it to tackle a variety of cutting tasks, from trimming branches to felling medium-sized trees. The engine is designed for high performance while still ensuring fuel efficiency, making it an economical choice for users who require a balance between power and runtime.

A key feature of the Poulan 414741 is its LowVib technology, which significantly reduces vibration levels during operation. This innovation allows users to work longer without discomfort, providing a more pleasant cutting experience. The chainsaw is designed with an ergonomic handle that aids in maintaining a secure grip, further enhancing user comfort and control.

The Poulan 414741 also incorporates an automatic chain oiler system that ensures consistent lubrication of the chain and bar, promoting a longer lifespan and optimal cutting performance. This feature minimizes the need for manual intervention, allowing users to focus on their tasks without interruption. Additionally, the easy-access air filter and spark plug ensure straightforward maintenance, making it simple for owners to keep their chainsaw in peak condition.

Safety is a priority in the design of the Poulan 414741. The chainsaw comes equipped with a chain brake that engages immediately in the event of kickback, preventing potential accidents. A hand guard also provides added protection to the user's hands from debris and chainsaw kickback.

Weighing in at a manageable size, the Poulan 414741 is easy to maneuver during operation, making it suitable for various cutting jobs, including landscaping, firewood preparation, and even rugged outdoor projects. Whether you’re an avid gardener or a professional logger, this model’s combination of power, comfort, and safety features makes it an excellent choice for anyone in need of a reliable chainsaw.

In conclusion, the Poulan 414741 exemplifies effectiveness and reliability in cutting tools, offering users a high-quality, easy-to-use chainsaw loaded with modern technology and features.
Top Page Image Contents