Poulan 414741 owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the en- gine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. Ithasbeendesigned,engineeredandmanufactured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity 4.0 Quarts (4,54 Liters)

and Type: Unleaded Regular only

Oil Type

SAE 5W-30 or 10W-30

(API SG–SL):

(0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces (0,74 Liters)

 

 

Spark Plug

Champion RJ19LM

Gap:

0.030" (0,072 mm)

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

5-7

OPERATION

8-13

MAINTENANCE

14-15

MAINTENANCE SCHEDULE

14

SERVICE AND ADJUSTMENTS

16-18

STORAGE

18

TROUBLESHOOTING

19

REPAIR PARTS

20-31

3 WARRANTY

32

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting 2220 KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP11530ES Handles Repair Parts Snow Thrower Model PP11530ES Handles Repair Parts Drive Repair Parts Snow Thrower Model PP11530ES Drive Page 417014X428 KEY Part DescriptionRepair Parts Snow Thrower Model PP11530ES Wheels / Decals Repair Parts Limited Warranty

414741 specifications

The Poulan 414741 is a versatile and powerful chainsaw designed to meet the needs of both seasoned professionals and occasional users. With a blend of innovation, durability, and user-friendly features, this model stands out in the competitive market of handheld power tools.

One of the defining characteristics of the Poulan 414741 is its robust engine. Equipped with a reliable 40cc two-stroke engine, this chainsaw delivers impressive power that allows it to tackle a variety of cutting tasks, from trimming branches to felling medium-sized trees. The engine is designed for high performance while still ensuring fuel efficiency, making it an economical choice for users who require a balance between power and runtime.

A key feature of the Poulan 414741 is its LowVib technology, which significantly reduces vibration levels during operation. This innovation allows users to work longer without discomfort, providing a more pleasant cutting experience. The chainsaw is designed with an ergonomic handle that aids in maintaining a secure grip, further enhancing user comfort and control.

The Poulan 414741 also incorporates an automatic chain oiler system that ensures consistent lubrication of the chain and bar, promoting a longer lifespan and optimal cutting performance. This feature minimizes the need for manual intervention, allowing users to focus on their tasks without interruption. Additionally, the easy-access air filter and spark plug ensure straightforward maintenance, making it simple for owners to keep their chainsaw in peak condition.

Safety is a priority in the design of the Poulan 414741. The chainsaw comes equipped with a chain brake that engages immediately in the event of kickback, preventing potential accidents. A hand guard also provides added protection to the user's hands from debris and chainsaw kickback.

Weighing in at a manageable size, the Poulan 414741 is easy to maneuver during operation, making it suitable for various cutting jobs, including landscaping, firewood preparation, and even rugged outdoor projects. Whether you’re an avid gardener or a professional logger, this model’s combination of power, comfort, and safety features makes it an excellent choice for anyone in need of a reliable chainsaw.

In conclusion, the Poulan 414741 exemplifies effectiveness and reliability in cutting tools, offering users a high-quality, easy-to-use chainsaw loaded with modern technology and features.
Top Page Image Contents