Poulan 414639 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

Be sure snow thrower is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

Keep finished surfaces/wheels free of gasoline, oil, etc.

We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Image 15
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Storage Other TroubleshootingRepair Parts KEY Part Description 205 414280 Knob, Lever Handles Repair Parts Repair Parts Drive Repair Parts Page 417014X428 KEY Part DescriptionWheels / Decals KEY Part Description Limited Warranty

414639 specifications

The Poulan 414639 is a robust and efficient chainsaw designed for both professional arborists and homeowners alike. Known for its reliable performance and ease of use, this model has gained popularity among individuals who need a dependable tool for cutting firewood, trimming trees, or tackling larger landscaping projects.

One of the main features of the Poulan 414639 is its powerful engine. Equipped with a 42cc two-stroke engine, this chainsaw delivers the right amount of power to handle challenging cutting tasks. The engine operates efficiently, providing a seamless cutting experience while minimizing fuel consumption. This feature is especially beneficial for users who need to work for extended periods without frequent refueling.

The chainsaw comes with a 16-inch guide bar and low-profile chain, making it versatile for different cutting applications. Whether users are making fast cuts in smaller trees or pruning larger branches, the Poulan 414639 is designed to deliver smooth and efficient results. The low profile contributes to reduced kickback and enhances safety when operating the saw.

Another key characteristic of the Poulan 414639 is its user-friendly design. The lightweight construction allows for extended use without causing unnecessary fatigue, making it suitable for both novice and experienced users. Additionally, the ergonomic handle is designed for comfort, providing a secure grip that enhances control during operation.

Safety features are also a priority in this model. The chainsaw is equipped with a chain brake for instant stopping in case of kickback, ensuring the operator's safety. The saw also features an inertia-activated chain brake that engages automatically when it detects sudden changes in motion, adding an extra layer of protection.

Poulan incorporates advanced technologies into the 414639 model to improve performance and maintenance. The Easy Start system ensures that starting the chainsaw is hassle-free, reducing the effort required to get it running. This technology is particularly valuable for those who may struggle with traditional pull-start mechanisms. Furthermore, the tool-less chain tensioning system allows users to adjust the chain’s tension quickly and easily, ensuring optimal performance at all times.

In conclusion, the Poulan 414639 is an excellent chainsaw that combines power, safety, and user-friendly features. With its reliable performance and thoughtful design, it caters to the needs of both casual users and professionals, making it a valuable addition to anyone's toolkit. Whether tackling small projects or larger jobs, the Poulan 414639 is a lightweight, efficient, and dependable choice for tackling a variety of cutting tasks.