Poulan 414639 owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 22)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a Sears service centre/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest Sears service centre/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistantstand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

 

HOUSING

 

 

FIG. 22

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other TroubleshootingRepair Parts KEY Part Description 205 414280 Knob, Lever Handles Repair Parts Repair Parts Drive Repair Parts Page 417014X428 KEY Part DescriptionWheels / Decals KEY Part Description Limited Warranty

414639 specifications

The Poulan 414639 is a robust and efficient chainsaw designed for both professional arborists and homeowners alike. Known for its reliable performance and ease of use, this model has gained popularity among individuals who need a dependable tool for cutting firewood, trimming trees, or tackling larger landscaping projects.

One of the main features of the Poulan 414639 is its powerful engine. Equipped with a 42cc two-stroke engine, this chainsaw delivers the right amount of power to handle challenging cutting tasks. The engine operates efficiently, providing a seamless cutting experience while minimizing fuel consumption. This feature is especially beneficial for users who need to work for extended periods without frequent refueling.

The chainsaw comes with a 16-inch guide bar and low-profile chain, making it versatile for different cutting applications. Whether users are making fast cuts in smaller trees or pruning larger branches, the Poulan 414639 is designed to deliver smooth and efficient results. The low profile contributes to reduced kickback and enhances safety when operating the saw.

Another key characteristic of the Poulan 414639 is its user-friendly design. The lightweight construction allows for extended use without causing unnecessary fatigue, making it suitable for both novice and experienced users. Additionally, the ergonomic handle is designed for comfort, providing a secure grip that enhances control during operation.

Safety features are also a priority in this model. The chainsaw is equipped with a chain brake for instant stopping in case of kickback, ensuring the operator's safety. The saw also features an inertia-activated chain brake that engages automatically when it detects sudden changes in motion, adding an extra layer of protection.

Poulan incorporates advanced technologies into the 414639 model to improve performance and maintenance. The Easy Start system ensures that starting the chainsaw is hassle-free, reducing the effort required to get it running. This technology is particularly valuable for those who may struggle with traditional pull-start mechanisms. Furthermore, the tool-less chain tensioning system allows users to adjust the chain’s tension quickly and easily, ensuring optimal performance at all times.

In conclusion, the Poulan 414639 is an excellent chainsaw that combines power, safety, and user-friendly features. With its reliable performance and thoughtful design, it caters to the needs of both casual users and professionals, making it a valuable addition to anyone's toolkit. Whether tackling small projects or larger jobs, the Poulan 414639 is a lightweight, efficient, and dependable choice for tackling a variety of cutting tasks.
Top Page Image Contents