Simplicity 1692569, 1692469, 1692570, 1691948, 1691900, 1691899 manual Specifications

Page 26

Specifications

ENGINE

Make	Tecumseh
Cylinders	1
Cycles	4
Crankshaft	Horizontal
8 HP
- Model No	See engine I.D. plate
- Bore & Stroke	3-1/8 in. x 2-17/32 in.
	(79.38 mm x 64.31 mm)
- Displacement	19.41 cu. in.
	(318.27 cc)
9 HP
- Model No	See engine I.D. plate
- Bore & Stroke	3-1/8 in. x 2-17/32 in.
	(79.38 mm x 64.31 mm)
- Displacement	19.41 cu. in.
	(318.27 cc)
10 HP
- Model No	See engine I.D. plate
- Bore & Stroke	3-3/16 in. x 2-17/32 in.
	(89.96 mm x 64.31 mm)
- Displacement	20.20 cu. in.
	(331.06 cc)
Ignition	Magneto
Governor	Mechanical
Choke	Manual
Lubrication	Splash system
Oil Capacity	See engine manual
Fuel Capacity	See engine manual

TRACTION DRIVE

Type	Friction drive transmission w/chain
	gear drive and speed selection
Speeds	Five forward and two reverse
Axle	Solid w/klik-pin lock for two-wheel drive
Tire Inflation	20 psi (137 kPa)

AUGER HOUSING

Construction	Welded steel stampings
Effective Width
- Model 8-60cm/24	24 in. (60 cm)
- Model 8-70cm/28	28 in. (70 cm)
- Model 9-70cm/28	28 in. (70 cm)
- Model 10-80cm/32	32 in. (80 cm)

Auger Opening Height		...........................19 in. (47.5 cm)
Spout Rotation	............................................	210 degrees
Scraper Bar	High Carbon, wear resistant steel
Skid Shoes		Adjustable, heat-treated steel

AUGER

Construction	Ribbon flite welded steel
Bearings	Self-lubricating

IMPELLER

Construction	..............................................4 steel blades
Bearings	Pre-lubricated and sealed ball bearing
Diameter	12 in. (30 cm)

AUGER & IMPELLER DRIVE

Type....................Cushion V-belt and worm gear housing

OVERALL DIMENSIONS & WEIGHT

Model 8-60cm/24
- Length	56-7/8 in. (142.18 cm)
- Width	26 in. (65 cm)
- Height	37-3/8 in. (93.44 cm)
- Weight	240 lbs. (109 kg)
Model 8-70cm/28
- Length	56-7/8 in. (142.18 cm)
- Width	30 in. (75 cm)
- Height	37-3/8 in. (93.44 cm)
- Weight	255 lbs. (115 kg)
Model 9-70cm/28
- Length	56-7/8 in. (142.18 cm)
- Width	30 in. (75 cm)
- Height	37-3/8 in. (93.44 cm)
- Weight	255 lbs. (115 kg)
Model 10-80cm/32
- Length	56-7/8 in. (142.18 cm)
- Width	34 in. (85 cm)
- Height	37-3/8 in. (93.44 cm)
- Weight	265 lbs. (120 kg)

SPECIFICATIONS ARE CORRECT AT TIME OF PRINTING AND ARE SUBJECT TO CHANGE WITHOUT NOTICE.

03

20

Image 26

Contents How to use this file...Operators Manuals Print Vendors Paper ManualsThis page Intentionally Blank OPERATOR’S Manual Page 24E Models 500 N. Spring Street, P.O. Box 997 Port Washington, WI Table Of Contents Preparation Safety RulesGeneral Maintenance & Storage OperationDischarge Chute Danger Decal Safety Signs & DecalsSafety Decals Auger Danger DecalEngine Controls ControlsSnowthrower Controls Starting Controls Electric Start Units OnlyDeflector Controls Ground Speed ControlsAuger Engage Control Scraper Height ControlOperation Checks Before Each START-UPWill Continue until the Free-Hand Control is released Starting the EngineOperating the Snowthrower Operators PositionDeflector Engine SpeedGround Speed Selector Scraper BAR & Skid ShoesKlik-Pin Outer Hole FREE-WHEELING Traction Drive LockAfter Each USE OFF-SEASON Storage Regular MaintenanceNormal Care Starting After StorageLubricate Point Where Control Rods Pass Through Bracket LubricationEngine fails to start ServiceTroubleshooting Engine starts hard or runs poorlyAuger rotates, but snow is not Scraper bar does not clean hardAuger does not stop when auger Thrown far enoughAuger Drive Tension Speed Selector AdjustmentBelt Replacement Traction Drive TensionMaintenance & Service Engine PulleyKeeper link Roller Chain ReplacementShear PIN Replacement Master link Direction of travelMounting Screws Discharge Control AdjustmentChecking Tire Pressure Specifications Technical Manual Availability Common Replacement PartsAccessories