Sears 143.804062, 536.885410 manual Tenance, Engine, Lubrication, Spark Plug

Page 15

TENANCE

ENGINE

LUBRICATION

Check the crankcase oil level (See Fig 17) before starting the engine and after each five (5) hours of con- tinuous use, Add S,A_E.,10W-30 motor oil or equivalenL Tighten the fill cap/dipstick securely each time you check the oil level, S,AE. 5W-30 motor oil may be used to make starting easier in areas where the temperature is consis- tently 20° F, or lower°

Change the oil after the first two hours of operation and every 25 hours thereafter or at }east once a year if the snow thrower is not used for 25 hours.• (See Fig., 18).

ePosition the snow thrower so the oil drain plug isthe lowest point on the engine_ Remove the oil drain plug and oil fill cap/dipstick, Drain the oil into a suit- able container. The oil will drain more freely when warm.

Replace the oit drain plug and tighten securely_ Refill the crankcase with SA.E_ 10W-30 motor oi!

(or equivalent)., S,A.E. 5W-30 motor oil may be used to make starting easier in areas where the temperature is consistently 20° F. or lower,

SPARK PLUG

oMake su re the spark plug is tightened securely into the engine and the spark plug wire is attached to the spark plug,,

oIf a torque wrench is available, torque the plug between 18 and 23 foot pounds.

Clean the area around the spark plug base before removal to prevent dirt from entering the engine.

Clean the spark plug and reset the gap periodicatly,

...................

 

 

MUST BE BETWEEN

 

 

 

FULL AND

 

 

 

ADD MARK

 

.

E(.

NOTE: OIL

LEVEL

 

-

, _.............,, i ,ll ii

ill i

ii

FIG, 17

OIL FILL CAP/

DIPSTICK

@

OJL DRAIN

PLUG

" " ; ..........FIGI ........

15

Image 15
Contents 536.885410 Fuel .SAFETY Safety RulesSafety Safety RU LESCustomer Responsibilities Maintenance AgreementINDEX Table of ContentsAsse L¥ Contents of Shipping CartonTo SET the Skid Height HOW to SET UP Your Snow ThrowerTo Remove Snow Thrower From Carton See FigTo CHECK/ADJUST Clutch Control Cables OPE AT O To Throw Snow HOW to USE Your Snow ThrowerTo Control Snow Discharge To Move Forward and BackwardFILL! ADD OIL To USE Weight Transfer SystemOperation Before Starting the ENGtNEFill GAS OPEAtio To Start EngineFrozen Starter Snow Throwing TipsWarm Start AS Required Genera L RECONMENDATiONSSnow Thrower After First USESpark Plug TenanceEngine LubricationServmce Andadjust E TS To Adjust Chute Crank AssemblyTo Adjust Scraper BAR To Adjust Belts To Adjust the Clutch Control CablesTo Replace Belts Auger Drive BeltRack Drive Belt To Adjust the Friction Wheel Serv Cean Adjustme TSTo Replace Friction Wheel Service a Adjust E T$To Adjust Track Service and Adjustme TSTo Adjust or Replace Spark Plug To Adjust CarburetorSnow Thrower EngineOther Servuce Iservice Records ScheduleLubrbcation Chart DationsCorrection Trouble CauseCraftsman 20 Snow Thrower Snow Thrower CraftsmanCraftsman 20 Snow Thrower Part Name Craftsman 23 Snow Thrower NO. Part NO. Part Name 21 o Part 536.885410PFTSMAH4=YL N6iH MODELNUMBER143.804062 RTSMAN 4oyCLEENGINE FT$ N 4=GCLEGmN Rewind Starter NOr Owners UAL When Ordering Repair PARTS, Always