Troy-Bilt 772C0767 Operating Tips, Chute Assembly, Auger Control, Drive Control and Shift Lever

Page 11

Drift

Cutter

Carriage Screws

& Hex Nuts

Figure 9

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

NOTE: The temperature of the muffler and the surrounding areas may exceed 150°F (65°C).

•For the most efficient snow removal, remove snow immediately after it falls.

•Discharge the snow downwind whenever possible.

•Slightly overlap each previous path.

•Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.

•Be certain to follow the precautions found in the “To Stop Engine” section to prevent possible freeze-up.

•Clean the snow thrower thoroughly after each use.

SECTION 5: MAKING ADJUSTMENTS

WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to “Know Your Snowthrower” for instructions.

The remote chute control cables have been pre- adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

Auger Control

Refer to Auger Control Test in the Operating Section to adjust the auger control.

Drive Control and Shift Lever

To check the adjustment of the drive control and shift lever, proceed as follows:

•With the engine off, move the shift lever all the way forward to the highest speed. With the drive control lever released, push the snow thrower forward. The unit should roll forward. Then engage the drive control. The tracks should stop turning.

•Now release the drive control and push the unit again.

•Move the shift lever back to the fast reverse position then all the way forward again. There should be no resistance in the shift lever, and the tracks should keep turning.

•If you have resistance when moving the shift lever or the tracks stop when they should not, loosen the jam nut on the drive control cable and unthread the cable one turn.

•If the tracks do not stop when you engage the drive control, loosen the jam nut on the drive control cable and thread the cable in one turn.

•Recheck the adjustment and repeat as necessary. Tighten the jam nut to secure the cable when correct adjustment is reached.

WARNING: Drain the gasoline out of the snow thrower’s tank, or place a piece of plastic film under the gas cap to avoid spillage BEFORE making the adjustment.

To test further for correct adjustment, if necessary, proceed as follows:

•Tip the snow thrower forward, allowing it to rest on the auger housing. See Figure 10.

•Remove the frame cover underneath the snow thrower by removing the six self-tapping screws.

•With the drive control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever. See Figure 11.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesDo not modify engine Maintenance And StorageAssembling Your Snow Thrower Drive Control / Auger Control Lock Clean-Out ToolKnow Your Snowthrower Shift Lever Heated Handles Switch on some modelsChute Crank Auger Drive ControlOperating Your Snow Thrower Recoil Starter To Stop EngineTo Engage Drive To Engage AugersAuger Control Test Drift Cutters If EquippedDrive Control and Shift Lever Chute AssemblyOperating Tips Auger ControlShift Rod Adjustment Lubrication Maintaining Your Snow ThrowerCarburetor Shave Plate and Skid Shoes Servicing Your Snow ThrowerAugers Auger Belts Belt Removal And ReplacementDrive Belt Replacing Friction Wheel RubberOff-Season Storage EngineProblem Cause Remedy TroubleshootingTWO Year Supreme Warranty Parts LISTS/LISTE DE Pièces Détachées Part RÉF Pièce Description 31A-701 Page 2227 38 44 31A-702 05.9.05 Page 31A-703 05.9.05 22 20 31A-704 352 31A-705 05.9.05 ANS Deux DE Suprème Garantie 9 Chapitre Dépannage DE Guide 8 Chapitre Remisage de Instructions Frottement Patins et Lame Courroies les de RemplacementEntretien 7 Chapitre TarièresPanneau LubrificationPatin Vitesses de levier du Tige’éjection Goulotte Tarière la de CommandeVitesses de levier et transmission la de Commande LA DE Dégagement DE Outil ’utilisation Conseils’entraînement de Embrayage Tarières les de EmbrayageDémarrage le Avant ’huile et d’essence PleinsGoulotte la de Manivelle Vitesses de Levier ’inclinaison de CommandeBlocage l’entraînement de Commande Tarière la de commande la de’assemblage pour requis Articles Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage AvantÉchéant Remisage ET Entretien Formation PréparationMoteur DE Information ’utilisation Notice

772C0767 specifications

The Troy-Bilt 772C0767 is a versatile and powerful string trimmer designed for homeowners and landscaping professionals who need an efficient tool for maintaining gardens, yards, and outdoor spaces. One of the standout features of this trimmer is its reliable engine, which delivers impressive performance and a consistent cutting power, making it ideal for tackling tough grass and weeds.

Equipped with a 159cc auto choke engine, the Troy-Bilt 772C0767 offers ease of starting and smooth operation, reducing the time you spend preparing to work. The innovative Easy Start technology is designed to minimize the effort required to start the trimmer, allowing users to quickly get to work without the frustrations often associated with traditional starting methods.

The trimmer boasts a 17-inch cutting width, enabling expansive coverage and efficiency as you navigate through larger areas. This cutting width makes it suitable for working around flower beds, fences, and other obstacles while providing a clean and precise cut. Furthermore, the dual-line bump head allows for quick line advancement, ensuring that you can keep cutting without frequent interruptions.

A significant aspect of the Troy-Bilt 772C0767 is its lightweight and ergonomically designed frame. Weighing in at just under 11 pounds, this trimmer is easy to maneuver and reduces user fatigue during longer tasks. The comfortable handle grip enhances control, while the adjustable shaft accommodates users of different heights, making it suitable for a wide range of individuals.

In addition to its physical features, the Troy-Bilt 772C0767 incorporates advanced technologies such as the Turbo-Spin feature. This unique design allows for better airflow around the trimmer line, improving cutting efficiency and ensuring optimal performance in various mowing conditions.

Durability is also a key characteristic of the Troy-Bilt 772C0767. Built with high-quality materials, this trimmer is designed to withstand regular use in tough outdoor environments. The solid construction ensures reliability, allowing you to invest in a tool that will serve you well over time.

Overall, the Troy-Bilt 772C0767 string trimmer combines power, efficiency, and user-friendly features to create an essential tool for anyone looking to maintain their yard or garden. With its combination of innovative technologies and quality construction, this trimmer is a smart choice for all your trimming needs.
Top Page Image Contents