Troy-Bilt 772C0767 manual Skid Shoe, Shift Rod Adjustment

Page 12

 

 

hole in the shift lever. See Figure 12.

 

Frame Cover

• Insert ferrule from the left side of the snow thrower

 

into the upper hole.

 

 

 

 

 

 

• Reinstall the hairpin clip and the washer.

 

 

 

Shift Lever

 

 

Hairpin Clip

 

 

 

Flat

Ferrule

 

 

 

Auger

 

Washer

Upper Shift Rod

Housing

 

 

 

 

 

 

 

Shift Rod

Hairpin Clip

 

 

Connector

 

 

Figure 10

 

Lower Shift Rod

 

 

 

•With the traction control lever engaged, the friction wheel must contact the drive plate. See Figure 11.

If adjustment is necessary:

•Loosen the jam nut on the traction cable and thread the cable in or out as necessary.

•Retighten the jam nut to secure the cable when correct adjustment is reached.

•Reassemble the frame cover.

Gear Shaft

Drive

Cable

Friction Wheel

Pivot Rod

 

Rubber

 

 

Drive

 

Plate

Figure 11

NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower.

Shift Arm

Figure 12

IMPORTANT: Make certain to check for correct adjustment of the shift rod as instructed under “Drive Control and Shift Lever” on page 11, before operating the snow thrower.

Skid Shoe

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position. See Figure 13.

Adjust skid shoes as follows:

•Loosen, but do not remove, the three hex nuts which fasten the skid shoe to the auger housing.

•Raise or lower the skid shoe to desired position.

•Retighten the hex nuts loosened earlier.

•Repeat on the other side of the snow thrower.

Shift Rod Adjustment

•Remove the hairpin clip and flat washer from the shift handle under the handle panel. See Figure 12.

•Place shift lever in sixth (6) position or fastest forward speed.

•Push shift arm assembly down as far as it will go.

•Rotate the ferrule up or down on the shift rod as necessary until the ferrule lines up with the upper

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Do not modify engineAssembling Your Snow Thrower Clean-Out Tool Know Your SnowthrowerDrive Control / Auger Control Lock Heated Handles Switch on some models Chute CrankAuger Drive Control Shift LeverOperating Your Snow Thrower To Stop Engine To Engage DriveTo Engage Augers Recoil StarterDrift Cutters If Equipped Auger Control TestChute Assembly Operating TipsAuger Control Drive Control and Shift LeverShift Rod Adjustment Maintaining Your Snow Thrower CarburetorLubrication Servicing Your Snow Thrower AugersShave Plate and Skid Shoes Belt Removal And Replacement Auger BeltsReplacing Friction Wheel Rubber Drive BeltEngine Off-Season StorageTroubleshooting Problem Cause RemedyTWO Year Supreme Warranty Parts LISTS/LISTE DE Pièces Détachées Part RÉF Pièce Description 31A-701 Page 2227 38 44 31A-702 05.9.05 Page 31A-703 05.9.05 22 20 31A-704 352 31A-705 05.9.05 ANS Deux DE Suprème Garantie 9 Chapitre Dépannage DE Guide 8 Chapitre Remisage de Instructions Frottement Courroies les de Remplacement Patins et LameTarières Entretien 7 ChapitreLubrification PanneauVitesses de levier du Tige PatinTarière la de Commande Vitesses de levier et transmission la de Commande’éjection Goulotte ’utilisation Conseils LA DE Dégagement DE OutilTarières les de Embrayage ’entraînement de Embrayage’huile et d’essence Pleins Démarrage le AvantGoulotte la de Manivelle ’inclinaison de Commande Vitesses de LevierTarière la de commande la de Blocage l’entraînement de CommandeGoulotte la de manivelle la de Montage Guidon du Montage’assemblage Avant ’assemblage pour requis ArticlesÉchéant Remisage ET Entretien Préparation FormationMoteur DE Information ’utilisation Notice

772C0767 specifications

The Troy-Bilt 772C0767 is a versatile and powerful string trimmer designed for homeowners and landscaping professionals who need an efficient tool for maintaining gardens, yards, and outdoor spaces. One of the standout features of this trimmer is its reliable engine, which delivers impressive performance and a consistent cutting power, making it ideal for tackling tough grass and weeds.

Equipped with a 159cc auto choke engine, the Troy-Bilt 772C0767 offers ease of starting and smooth operation, reducing the time you spend preparing to work. The innovative Easy Start technology is designed to minimize the effort required to start the trimmer, allowing users to quickly get to work without the frustrations often associated with traditional starting methods.

The trimmer boasts a 17-inch cutting width, enabling expansive coverage and efficiency as you navigate through larger areas. This cutting width makes it suitable for working around flower beds, fences, and other obstacles while providing a clean and precise cut. Furthermore, the dual-line bump head allows for quick line advancement, ensuring that you can keep cutting without frequent interruptions.

A significant aspect of the Troy-Bilt 772C0767 is its lightweight and ergonomically designed frame. Weighing in at just under 11 pounds, this trimmer is easy to maneuver and reduces user fatigue during longer tasks. The comfortable handle grip enhances control, while the adjustable shaft accommodates users of different heights, making it suitable for a wide range of individuals.

In addition to its physical features, the Troy-Bilt 772C0767 incorporates advanced technologies such as the Turbo-Spin feature. This unique design allows for better airflow around the trimmer line, improving cutting efficiency and ensuring optimal performance in various mowing conditions.

Durability is also a key characteristic of the Troy-Bilt 772C0767. Built with high-quality materials, this trimmer is designed to withstand regular use in tough outdoor environments. The solid construction ensures reliability, allowing you to invest in a tool that will serve you well over time.

Overall, the Troy-Bilt 772C0767 string trimmer combines power, efficiency, and user-friendly features to create an essential tool for anyone looking to maintain their yard or garden. With its combination of innovative technologies and quality construction, this trimmer is a smart choice for all your trimming needs.
Top Page Image Contents