Troy-Bilt 769-03244 Gas & Oil Fill-Up, Stopping The Engine, Electric Starter on certain models

Page 10

WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

If your home’s wir- ing system is not a three-wire grounded system, do not use this electric starter under any conditions.

If your home electrical system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in the separate engine manual packed separately with your snow thrower. Read instructions carefully.

Starting The Engine

1.Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

2.Make certain both the auger control and drive control are in the disengaged (released) position.

3.Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start unless the key is inserted into ignition switch.

Electric Starter (on certain models)

1.Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

1.Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

2.Rotate choke control to FULL choke position (for a cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

3.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

4.Push starter button to start engine.

5.Once the engine starts, immediately release starter button.

6.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to FULL and then slowly into the OFF position again.

7.When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

Recoil Starter

1.Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

2.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

NOTE: Additional priming may be necessary if the temperature is below 15° F. (-9° C).

3.Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil.

4.Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil.

5.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and then slowly into the OFF position again.

NOTE: Allow the engine to warm up for a few minutes after starting. The engine will not develop full power until it reaches operating temperatures.

Stopping The Engine

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

•To help prevent possible starter freeze-up, proceed as follows:

Electric Starter (on certain models)

1.Connect extension cord to the electric starter outlet on the engine, then to 120 volt AC outlet.

2.With the engine running, push the starter button and allow the starter for spin for several seconds. The noise made by the starter is normal. The engine’s starter is not being harmed.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Two-Stage Snow Thrower 769-03244Finding and Recording Model Number Table of ContentsCustomer Support Chute Clean-out Tool Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Your Snow Thrower Lamp Wiring Harness If equipped Clean-Out ToolHousing Ice from the chuteOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter on certain models Recoil Starter To Engage DriveTo Engage Augers Auger Control TestShift Cable Making AdjustmentsChute Assembly optional Drive ControlTire Pressure Chute Bracket AdjustmentProperty Lubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Drive Belt Replacement Remove and replace belt in the reverse orderFriction Wheel Removal Remove the rubber ring from between the platesOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty TWO Year Limited WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différentPart Description RÉF Pièce 31AE6GKF500 Part

769-03244 specifications

The Troy-Bilt 769-03244 is a versatile and powerful garden tiller designed for homeowners and gardening enthusiasts seeking to cultivate their outdoor spaces efficiently. This tiller stands out for its robust features, advanced technologies, and user-friendly characteristics, making it an ideal choice for both seasoned gardeners and those new to gardening.

One of the main features of the Troy-Bilt 769-03244 is its powerful 4-cycle engine, which provides sufficient torque and durability needed to break up tough soil and prepare it for planting. The engine’s design ensures lower emissions and quieter operation compared to conventional 2-cycle engines, making it a more environmentally friendly option. The rear-tine tiller design allows for better balance and control, ensuring that users can maneuver it effortlessly across various terrains.

Another significant characteristic is the tiller's adjustable tilling width. The Troy-Bilt 769-03244 comes with a tilling width of up to 16 inches, which can be adjusted depending on the size and needs of your garden. This feature enhances its versatility, allowing it to work well in tight spaces or larger plots of land. Moreover, the tiller offers a tilling depth of up to 8 inches, ensuring thorough soil preparation, which is crucial for healthy plant growth.

The Troy-Bilt 769-03244 also incorporates the company’s patented “Counter-Rotating Tines” technology. This feature allows the tines to spin in the opposite direction of the tiller’s forward motion, providing superior soil penetration and reducing the risk of the tiller bouncing or skipping across the ground. This innovation not only enhances tilling efficiency but also improves soil aeration, leading to healthier root systems for your plants.

Additional user-friendly characteristics include the adjustable handle, which can be modified to accommodate different heights for operator comfort and ease of control. The tiller’s lightweight design makes it easier to transport and store, adding to its practicality.

In summary, the Troy-Bilt 769-03244 is an excellent investment for anyone looking to cultivate their garden with ease and efficiency. Its powerful engine, adjustable tilling width and depth, counter-rotating tines technology, and user-centric design features work in harmony to create a tilling experience that is both effective and enjoyable. Whether you are preparing a new garden bed or maintaining an existing one, this tiller is equipped to meet your gardening needs with reliability and performance.
Top Page Image Contents