Troy-Bilt 769-03244 warranty $26% #/.42

Page 9

Auger Control

!5'%2

#/.42/,

'/

The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop.

Drive Control/ Auger Control Lock

$2)6%

#/.42/,

'/

The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive. Release to stop.

The drive control also locks the auger control so you can operate the chute directional control without interrupting the snow throwing process. If the auger control is en- gaged simultaneously with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release both controls to stop the augers and wheel drive.

IMPORTANT: Always release the drive control before changing speeds.

Two-Way Chute Control™ (optional)

This two-way control lever is meant to control the distance of snow discharge from the chute. Tilt the lever forward or rearward to adjust the distance snow will be thrown.

•To change the angle/distance which snow is thrown, pivot the joy-stick forward or backward.

Chute Directional Control (optional)

The chute directional control is located on left side of the snow thrower.

To change the direction in which snow is thrown, turn chute directional control as follows:

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

#(54%5$)2%#4)/.!,2#/.42/,

$)3#(!2'%

$)3#(!2'%

,%&4

2)'(4

#(54%54),4 $/7.

#(54%54),4

50

Ignition Key

The ignition key must be inserted and snapped in place in order for the engine to start. Remove the ignition key to prevent unauthorized use of equipment. Do NOT attempt to turn the key.

Chute Clean-Out Tool

The clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip.

1.Release both the auger control and the drive/auger control lock.

2.Stop the engine by moving the throttle to the stop position.

3.Remove the clean-out tool from the mounting clip.

4.Use the shovel-shaped end of the clean-out tool to remove any snow and ice in the chute assembly.

5.Re-fasten the clean-out tool to the mounting clip on the rear of the auger housing and restart engine.

6.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow or ice from the chute assembly before continuing to clear snow.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Augers

When engaged, the augers rotate and draw snow into the auger housing.

4

Operating

Your Snow

Thrower

WARNING

The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear safety glasses while operating the snow thrower, or while performing any adjust- ments or repairs on it.

Be sure no one other than the operator is standing near the snow thrower while starting engine or operating snow thrower. Never run engine indoors or in enclosed, poorly ventilated areas. En- gine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and snow thrower.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 769-03244 Two-Stage Snow ThrowerTable of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Chute Clean-out ToolTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Housing Clean-Out ToolLamp Wiring Harness If equipped Ice from the chuteKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Stopping The EngineElectric Starter on certain models To Engage Augers To Engage DriveRecoil Starter Auger Control TestChute Assembly optional Making AdjustmentsShift Cable Drive ControlChute Bracket Adjustment Tire PressureProperty Engine Maintaining Your Snow ThrowerLubrication Shave Plate and Skid ShoesAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Remove and replace belt in the reverse order Drive Belt ReplacementRemove the rubber ring from between the plates Friction Wheel RemovalWipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble ShootingTWO Year Limited Warranty WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce Remarque Lhabitacle peut être légèrement différent 30 in/poPart Description RÉF Pièce 31AE6GKF500 Part

769-03244 specifications

The Troy-Bilt 769-03244 is a versatile and powerful garden tiller designed for homeowners and gardening enthusiasts seeking to cultivate their outdoor spaces efficiently. This tiller stands out for its robust features, advanced technologies, and user-friendly characteristics, making it an ideal choice for both seasoned gardeners and those new to gardening.

One of the main features of the Troy-Bilt 769-03244 is its powerful 4-cycle engine, which provides sufficient torque and durability needed to break up tough soil and prepare it for planting. The engine’s design ensures lower emissions and quieter operation compared to conventional 2-cycle engines, making it a more environmentally friendly option. The rear-tine tiller design allows for better balance and control, ensuring that users can maneuver it effortlessly across various terrains.

Another significant characteristic is the tiller's adjustable tilling width. The Troy-Bilt 769-03244 comes with a tilling width of up to 16 inches, which can be adjusted depending on the size and needs of your garden. This feature enhances its versatility, allowing it to work well in tight spaces or larger plots of land. Moreover, the tiller offers a tilling depth of up to 8 inches, ensuring thorough soil preparation, which is crucial for healthy plant growth.

The Troy-Bilt 769-03244 also incorporates the company’s patented “Counter-Rotating Tines” technology. This feature allows the tines to spin in the opposite direction of the tiller’s forward motion, providing superior soil penetration and reducing the risk of the tiller bouncing or skipping across the ground. This innovation not only enhances tilling efficiency but also improves soil aeration, leading to healthier root systems for your plants.

Additional user-friendly characteristics include the adjustable handle, which can be modified to accommodate different heights for operator comfort and ease of control. The tiller’s lightweight design makes it easier to transport and store, adding to its practicality.

In summary, the Troy-Bilt 769-03244 is an excellent investment for anyone looking to cultivate their garden with ease and efficiency. Its powerful engine, adjustable tilling width and depth, counter-rotating tines technology, and user-centric design features work in harmony to create a tilling experience that is both effective and enjoyable. Whether you are preparing a new garden bed or maintaining an existing one, this tiller is equipped to meet your gardening needs with reliability and performance.
Top Page Image Contents