Assembly, Unpacking | Yard Machines E6C0F, E610E, E660G, E640F, E600E

SECTION 4: ASSEMBLY

AUGER SHEAR BOLTS (SPARES)

											Hex Lock Nuts


	Shear Bolts
	Shear Bolts										5/16” Thread
	(710-0890A)										(712-0429)

NOTE: The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a hard foreign object or ice jam, the snow thrower is designed so that the bolts may shear. Two replace- ment shear bolts and nuts are provided for your con- venience. Store in a safe place until needed.

IMPORTANT: NEVER replace the auger shear bolts with standard hex bolts. Any damage to the auger gearbox or other components as a result of doing so will NOT be covered by your snow thrower’s warranty.

UNPACKING

1.Remove the screws from the top, sides and ends of the shipping crate.

2.Set top panel aside to avoid tire punctures or personal injury.

3.Remove and discard plastic bag that covers unit.

4.Carefully roll unit out of crate.

IMPORTANT: After assembly, service engine with gasoline, and check oil level as instructed in the separate engine manual packed with your unit.

NOTE: All references to right or left side of the snow thrower are determined from behind the unit in the operating position.

ASSEMBLY

1.Remove the lower two plastic wing nuts, cupped washers and carriage bolt (eyebolt on the left side) from the lower handle. See Figure 3.

2.Raise the upper handle assembly until it aligns with lower handle.

3.Be sure both cables are aligned with cable roller guides located in the lower rear of snow thrower frame.

4.Secure the upper handle and lower handle with the plastic wing nuts, cupped washers, and car- riage bolt (eyebolt on the left side) previously removed.

	Cupped
	Washer
Carriage	Upper
Bolt	Handle
	Wing
	Nuts
	Lower
	Handle

Figure 3

5.Adjust the eyebolt on the chute directional control so the control rod does not come into contact with the engine by moving the hex nut against the handle (if necessary). Retighten the wing nut to secure the chute directional control in this position. See Figure 4.

6.Slide the shift rod connector down over the end of the lower shift rod. Tap the top of connector until it locks on the lower shift rod.

Upper
Shift Rod	Shift Rod
	Shift Rod
Hex Nut	Connector
Hex Nut
	Lower
	Shift Rod
Eyebolt

Figure 4

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to shift gears or change directions.

7.Unwrap the headlight wire which is attached to the headlight, beneath the handle panel. Wind it around the right handle several times to remove excess slack in the wire. See Figure 5.

8.Plug the wire from the headlight into the wire lead coming from the right side of the engine, underneath the fuel tank.

E600E, E640F, E660G, E610E, E6C0F specifications

Yard Machines has built a solid reputation for producing robust and reliable lawn equipment, and the E600E, E6C0F, E640F, E610E, and E660G models are no exception. Each model combines advanced features and innovative technologies, making them ideal for homeowners seeking efficient lawn care solutions.

The Yard Machines E600E is designed for exceptional performance. It features a powerful engine that delivers reliable starting and consistent cutting power. The compact design allows for easy maneuverability around tight spaces, while its adjustable cutting height ensures a customized finish for various types of grass. The E600E also includes a mulching capability that recycles grass clippings, promoting a healthier lawn.

The E6C0F model stands out with its user-friendly controls, allowing even novice users to handle it with ease. This model incorporates a self-propelled system, which reduces user fatigue during extended periods of use. The durable construction and high-quality materials used in the E6C0F ensure longevity, allowing homeowners to tackle their lawns season after season without the worry of wear and tear.

Moving to the E640F, this model is equipped with an advanced cutting deck technology that delivers a cleaner cut and better grass management. The E640F’s ergonomic design enhances comfort, featuring a padded handle and lightweight body. Additionally, this model offers various speed settings to adapt to different mowing conditions, ensuring an efficient and effective mowing experience.

The E610E model is recognized for its versatility. With multiple attachment options, the E610E can easily switch from mowing to other tasks, such as leaf collection or aeration. Its robust engine ensures it can handle tougher jobs, giving homeowners the flexibility needed for year-round lawn maintenance.

Lastly, the E660G is a powerhouse in the Yard Machines lineup. It comes with a high-capacity bagging system that reduces the frequency of emptying during mowing sessions. The E660G also features all-wheel drive, providing superior traction on uneven terrain. Its sleek design and enhanced aesthetics make it a stylish addition to any tool shed.

In summary, the Yard Machines E600E, E6C0F, E640F, E610E, and E660G models are engineered to meet various lawn care needs, blending performance, efficiency, and ease of use. Whether for simple residential mowing or more complex landscaping tasks, these mowers prove to be invaluable assets for any homeowner. Each model showcases Yard Machines' commitment to quality and innovation in lawn care technology.