Craftsman 917.881064 owner manual Inten CE, Engine, Cleaning

Page 16

INTEN CE

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See "TO REMOVE BELT COVER" in the Service and Adjustments section of this manual).

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction

wheel and damage to the drive system of your snow thrower.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classification SG-SL. Select the oil'sSAE viscosity grade according to your expected operating temperature.

SAE ViSCOSiTY GRADES

 

 

!

 

I

 

i °F

-20

 

0

30 32

40

i°c -30

-2o

40

6

lo

TEMPERATURE RANGE ANTiCiPATED

BEFORE NEXT OiL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F/0°C. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG-SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See "TO REMOVE WHEELS" in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Besureto install klick pin into proper hole in wheel axle (See "TO REMOVE WHEELS" in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at "FULE'line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark

plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual.

CLEANING

IMPORTANT." For best performance, keep snow thrower

housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

&WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

eKeep finished surfaces/wheels free of gasoline, oil, etc.

eWe do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents CRRFT$14Rli CautioSafe Operation Practices for Walk-Behind Snow Throwers Contents Limited 2-YEAR Warranty on Craftsman Snow Thrower Sears, Roebuck And Co., Hoffman Estates, ILAPI SG-SL RJ19LMParts Packe ELY I CartonHOW to SET UP Your Snow Thrower Unfold Upper HandleOperation See FigsAsse BLY/PRE-OPERATION Check TiRE PressureRead and Follow ALL Safety Information OperatiPrimer RUN Pull OUT to StopMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower Stopping Traction DriveAuger EngineLever To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Fuel. Do not store, spill or use gasolineTo Start Engine Before StoppingMaintenance section General RecommendationsBefore Each USE LubricationInten CE CleaningEngine Be sure the on/off switch is in the OFF position To Adjust Snow Thrower HeightADJ Ents Chute DeflectorService a ADJ Install Engine PulleyInstall Belt Cover Install DischargeSnow Thrower StorageOther Troubleshooti G ProblemCause Correction Tabla DE Materias Paratodaslasunidadesconmotoresdemandoel6ctrico GARANTiA Limitada DE 2 Anos DEL Lanzador DE Nieve Craftsman APISoporte DE Cabeza Giratoria Pernos Y Turcas Extra Para LA CizallaMando a Dstanca DEL Deflector DEL Conducto Montaje / PRE-OPE AcionSacar Desplegar LA Empunadura SuperiorMontaje / PRE-OPERACI Montaje DE LA BielaDE IVlANDO DE LA Traccion Vet Figs y DE Mando DE LA Barrena Vet Figs yMontaje / PRE-OPE Acion Montar EL Conducto DE Eyeccion / CabezaMontar EL Mando a Distancia DEL DEFLEC= Controlar LA Presion DE LOS NeumaticosOperac Familiarjcese CON SU Maquina QuitanievesAtencion Encendido Apagado Poner EN Marcha Extraer Para Apagar DESEN= GanchadoPERACl Cumple CON LOS Requisitos DE Seguridad DE LA A.N.SJComo Utilizar SU M.QUINA Quitanieves OPE AcionVet Fig Lanzar LA Nieve Vet Fig Una puesta en marcha accidentalIvioverse Adelante Y Atras Vet Fig Funcionamiento DE LA Direccion Vet FigControlar EL Nivel DE Aceite DEL Motor Regular LAS Placas DE DeslizamientoUsar LOS Cortadores DE Acuiviulaciones Consejos Para Lanzar LA Nieve Puesta EN Iviarcha DEL MotorPuesta EN Marcha CON EL Motor Frio Arrancador Electrico Antes DE PararNTO Tabla DE Recomendaciones GeneralesSAE 5W-30 Aceite del Motor En la seccion de Mantenimiento Grasa ParaAnte a to LimpiezaPara Ajustar LA Altura DE Iviaquina Quitanieves Conducto DeflectorOriginales entregados con la rnquina quita= nieves Pernos DE Seguridad Vet FigVaciar LA Gasolina DEL Deposito DE Carburante Sustituir LAS Correas Vea FigMontar LA Polea DE Transmision DEL Motor ACE I to CarburadorOtros Desmontar LAS Ruedas Vet FigCorreccion Exploded Description ImpellerAuger Housing Scrapper BAR KEY Part NO. noPart DescriptionSkid Plate LH Skid Plate RHPlastic Washer Drift Cutter BARKEY Shoulder Screw Plastic Washer CarriageLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotSpacer RetainerPivot Support Weldment Lower HandleKEY Part NO. no Interlock Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model Number 917,881064 Drive 3324 Drive Plate Assembly KEY Part Description Speed SelectorBottom PAN END Plate Spring Bracket ScrewEngine Mount Plate Frame WeldmentEngine Bolt 3/8-18 DESCRiPTiON Traction BeltCover Retainer RingWheel Driver Wheel LobeCable Bracket LH Cable Bracket RH Screw 1/4-20 X Wheel Assembly2KEY Power Cord KEY Part Safety Ignition KEYRetainer PIN WrenchInstruction Briggs & Stratton 4-CYCLE Engine Model Number 20M314-O927-E1 976 Model Number 20M314-0927=E1 Cylinder Assembly 130 Retainer-Governor Shaft Service Otes Service Notes Your Home Www,sears,com Www,sears,ca

917.881064 specifications

The Craftsman 917.881064 is a powerful and versatile riding lawn mower designed for homeowners seeking an effective solution for lawn care. This model is engineered to deliver precision and ease of use, making it an essential tool for maintaining a well-manicured yard.

One of the standout features of the Craftsman 917.881064 is its robust engine. Equipped with a reliable Briggs & Stratton engine, it ensures optimal power and performance. The engine provides a solid horsepower, allowing users to tackle tough mowing jobs with confidence. The automatic transmission enhances the riding experience, enabling smooth acceleration and deceleration, which is particularly beneficial when navigating around gardens and flower beds.

The cutting deck of the Craftsman 917.881064 is another highlight. With a generous cutting width, it allows for efficient mowing of larger areas in less time. It is adjustable, offering multiple cutting height options to customize the finish according to personal preferences. This feature is crucial for achieving the desired lawn appearance and ensuring healthy grass growth.

Technology plays a significant role in the functionality of this mower. The integrated mulching capability enables grass clippings to be finely shredded and returned to the lawn, providing essential nutrients and promoting a healthier turf. Furthermore, the mower features a side-discharge option, giving users flexibility in how they manage clippings.

Durability and comfort are key characteristics of the Craftsman 917.881064. The heavy-duty frame and high-quality materials used in construction ensure it can withstand frequent use in various weather conditions. The plush, adjustable seat offers comfort during longer mowing sessions, making the experience more enjoyable.

Ease of maintenance is another important aspect. The mower is designed for straightforward maintenance procedures, with accessible components that simplify oil changes and blade replacements. This thoughtful design extends product life and enhances performance.

In summary, the Craftsman 917.881064 is a well-rounded riding lawn mower that combines power, efficiency, and comfort. With its sturdy construction, advanced features, and user-friendly technology, it provides an excellent solution for homeowners looking to maintain their lawns with minimal effort. Whether mowing, mulching, or simply enjoying the ride, this mower stands out as a reliable choice in the garden care domain.
Top Page Image Contents