Craftsman 917.881064 owner manual Asse BLY/PRE-OPERATION, Check TiRE Pressure

Page 8

ASSE BLY/PRE-OPERATION

iNSTALL DISCHARGE CHUTE / CHUTE ROTATOR

HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces-

sary, rotate chute assemblyto align square and pin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and Iocknut on threaded stud and tighten securely.

_3/8LOCKNUT

_3/8WASHER

iNSTALL CHUTE DEFLECTOR REMOTE CONTROL

(See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 Iocknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with

1/4-20 shoulder bolt, nylon washer and 1/4-20 Iocknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotator head and into hole in chute deflector as shown.

1/4-20

SPRING

SHOULDER

CHUTE

 

DEFLECTOR

 

HOOK

NYLON

BETWEEN

WASHER

HEX NUTS

 

ON CHUTE

1/4-20

ROTATO R

LOCKNUT

HEAD

CABLE

EYELET

CHUTE BRACKET

PiN

STUD

ROTATOR HEAD

CHUTEMOUNTING

ROTATOR HEAD BRACKET

FIG. 7

_B _EMOTE

CABLE

RACKET

5/16-18

LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROLLEVER

FIG. 9

CHECK TiRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CRRFT$14Rli CautioSafe Operation Practices for Walk-Behind Snow Throwers Contents Limited 2-YEAR Warranty on Craftsman Snow Thrower Sears, Roebuck And Co., Hoffman Estates, ILAPI SG-SL RJ19LMParts Packe ELY I CartonHOW to SET UP Your Snow Thrower Unfold Upper HandleOperation See FigsAsse BLY/PRE-OPERATION Check TiRE PressureRead and Follow ALL Safety Information OperatiPrimer RUN Pull OUT to StopMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower Stopping Traction DriveAuger EngineLever To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Fuel. Do not store, spill or use gasolineTo Start Engine Before StoppingMaintenance section General RecommendationsBefore Each USE LubricationEngine CleaningInten CE Be sure the on/off switch is in the OFF position To Adjust Snow Thrower HeightADJ Ents Chute DeflectorService a ADJ Install Engine PulleyInstall Belt Cover Install DischargeOther StorageSnow Thrower Cause Correction ProblemTroubleshooti G Tabla DE Materias Paratodaslasunidadesconmotoresdemandoel6ctrico GARANTiA Limitada DE 2 Anos DEL Lanzador DE Nieve Craftsman APIMando a Dstanca DEL Deflector DEL Conducto Pernos Y Turcas Extra Para LA CizallaSoporte DE Cabeza Giratoria Montaje / PRE-OPE AcionSacar Desplegar LA Empunadura SuperiorMontaje / PRE-OPERACI Montaje DE LA BielaDE IVlANDO DE LA Traccion Vet Figs y DE Mando DE LA Barrena Vet Figs yMontaje / PRE-OPE Acion Montar EL Conducto DE Eyeccion / CabezaMontar EL Mando a Distancia DEL DEFLEC= Controlar LA Presion DE LOS NeumaticosOperac Familiarjcese CON SU Maquina QuitanievesAtencion Encendido Apagado Poner EN Marcha Extraer Para Apagar DESEN= GanchadoPERACl Cumple CON LOS Requisitos DE Seguridad DE LA A.N.SJVet Fig OPE AcionComo Utilizar SU M.QUINA Quitanieves Lanzar LA Nieve Vet Fig Una puesta en marcha accidentalIvioverse Adelante Y Atras Vet Fig Funcionamiento DE LA Direccion Vet FigUsar LOS Cortadores DE Acuiviulaciones Regular LAS Placas DE DeslizamientoControlar EL Nivel DE Aceite DEL Motor Consejos Para Lanzar LA Nieve Puesta EN Iviarcha DEL MotorPuesta EN Marcha CON EL Motor Frio Arrancador Electrico Antes DE PararNTO Tabla DE Recomendaciones GeneralesSAE 5W-30 Aceite del Motor En la seccion de Mantenimiento Grasa ParaAnte a to LimpiezaPara Ajustar LA Altura DE Iviaquina Quitanieves Conducto DeflectorOriginales entregados con la rnquina quita= nieves Pernos DE Seguridad Vet FigMontar LA Polea DE Transmision DEL Motor Sustituir LAS Correas Vea FigVaciar LA Gasolina DEL Deposito DE Carburante ACE I to CarburadorOtros Desmontar LAS Ruedas Vet FigCorreccion Exploded Description ImpellerAuger Housing Scrapper BAR KEY Part NO. noPart DescriptionSkid Plate LH Skid Plate RHKEY Drift Cutter BARPlastic Washer Shoulder Screw Plastic Washer CarriageLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotSpacer RetainerKEY Part NO. no Lower HandlePivot Support Weldment Interlock Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model Number 917,881064 Drive 3324 Drive Plate Assembly KEY Part Description Speed SelectorBottom PAN END Plate Spring Bracket ScrewEngine Bolt 3/8-18 Frame WeldmentEngine Mount Plate DESCRiPTiON Traction BeltCover Retainer RingWheel Driver Wheel Lobe2KEY Wheel AssemblyCable Bracket LH Cable Bracket RH Screw 1/4-20 X Power Cord KEY Part Safety Ignition KEYRetainer PIN WrenchInstruction Briggs & Stratton 4-CYCLE Engine Model Number 20M314-O927-E1 976 Model Number 20M314-0927=E1 Cylinder Assembly 130 Retainer-Governor Shaft Service Otes Service Notes Your Home Www,sears,com Www,sears,ca

917.881064 specifications

The Craftsman 917.881064 is a powerful and versatile riding lawn mower designed for homeowners seeking an effective solution for lawn care. This model is engineered to deliver precision and ease of use, making it an essential tool for maintaining a well-manicured yard.

One of the standout features of the Craftsman 917.881064 is its robust engine. Equipped with a reliable Briggs & Stratton engine, it ensures optimal power and performance. The engine provides a solid horsepower, allowing users to tackle tough mowing jobs with confidence. The automatic transmission enhances the riding experience, enabling smooth acceleration and deceleration, which is particularly beneficial when navigating around gardens and flower beds.

The cutting deck of the Craftsman 917.881064 is another highlight. With a generous cutting width, it allows for efficient mowing of larger areas in less time. It is adjustable, offering multiple cutting height options to customize the finish according to personal preferences. This feature is crucial for achieving the desired lawn appearance and ensuring healthy grass growth.

Technology plays a significant role in the functionality of this mower. The integrated mulching capability enables grass clippings to be finely shredded and returned to the lawn, providing essential nutrients and promoting a healthier turf. Furthermore, the mower features a side-discharge option, giving users flexibility in how they manage clippings.

Durability and comfort are key characteristics of the Craftsman 917.881064. The heavy-duty frame and high-quality materials used in construction ensure it can withstand frequent use in various weather conditions. The plush, adjustable seat offers comfort during longer mowing sessions, making the experience more enjoyable.

Ease of maintenance is another important aspect. The mower is designed for straightforward maintenance procedures, with accessible components that simplify oil changes and blade replacements. This thoughtful design extends product life and enhances performance.

In summary, the Craftsman 917.881064 is a well-rounded riding lawn mower that combines power, efficiency, and comfort. With its sturdy construction, advanced features, and user-friendly technology, it provides an excellent solution for homeowners looking to maintain their lawns with minimal effort. Whether mowing, mulching, or simply enjoying the ride, this mower stands out as a reliable choice in the garden care domain.
Top Page Image Contents