Cub Cadet OEM-390-679 warranty Attaching the Chute Assembly, Attaching the Shift Rod

Page 7

Figure 3-4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 3-4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 3-5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

Attaching the Shift Rod

•Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 3-6.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) cannot be achieved, refer to the Adjustment Section.

•Normally the cable ties holding the steering cables against the handle are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Cut the excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide. See Figure 3-7.

3

Setting Up

Your Snow

Thrower

Figure 3-5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 3-6

Figure 3-7

7

Image 7

Contents 06/10/08 28, 30, 33 & 45Two-Stage Snow ThrowersOttawa Street South, KITCHENER, Ontario N2G 4J1 769-04103Finding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Carter d’engrenages moitié CG avec raccord graisse With or without grease fittingsStyle Page Part RÉF Pièce Description Rim Wheel Assembly DescriptionEnsemble de roue Description Roue Jante Roulement For parts and/or accessories refer to customer support on Page Com.mtdcanada GarantieGarantie cette de Pas couvre ne limitée garantie CetteDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansFrottement de Roue Entretien’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur duBoulon l’autre retirez Éloignez’enlevez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuPendantREMARQUEtourner moteur le Laissez Général d’ordre Recommandations’utilisation Conseils NormaleFaites Ne ’huile et d’essence PleinsGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Tiques Tarière la de CommandePneuma Bandages pneus des Pression Pas Bien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de SymbolesMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour04103-769 4J1 N2G Ontario KITCHENER, South, Street Ottawa