Cub Cadet OEM-390-679 warranty Auger Belt, Remove Loosen

Page 17

2.Remove the plastic belt cover, located near the engine, by removing the three self-tapping screws that secure it. See Figure 6-4.

3.a. Loosen the bolt shown in Figure 6-5 securing the

belt keeper bracket and remove the other bolt.

b.Push the belt keeper and bracket up off the engine pulley. See Figure 6-5.

Auger Belt

4.Remove the clip and flat washer from the ferrule in order to disconnect the auger idler rod from the brake bracket assembly. See Figure 6-6.

5.Slip the auger belt (the front belt) off the engine pulley.

6.Pull the brake bracket assembly towards the cable guide roller and unhook the auger cable “Z” fitting. See Figure 6-7.

7.From both sides of the the frame assembly, use a 1/2” wrench to remove the three hex tap screws securing the frame to the auger housing assembly. See Figure 6-8.

NOTE: Do not remove the lower hex flange lock nut on each side.

Figure 6-4

Remove

Loosen

Figure 6-5

Figure 6-6

Figure 6-7

Figure 6-8

6

Maintaining

Your Snow

Thrower

IMPORTANT

NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other com- ponents, as a result of doing so, will NOT be covered by your snow thrower’s warranty.

Check the condition of both auger belt and drive belt every 25 hours of snow thrower operation. Replace if either shows signs of wear and tear.

Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for refer- ence purposes only.

17

Image 17

Contents Ottawa Street South, KITCHENER, Ontario N2G 4J1 28, 30, 33 & 45Two-Stage Snow Throwers769-04103 06/10/08Customer Support Table of ContentsFinding and Recording Model Number There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeItems Required For Assembly Setting Up Your Snow ThrowerLoose Parts Assembling HandleAttaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Lamp WiringFinal Adjustments Drift Cutters If EquippedSkid Shoes Check the adjustment of the auger control as followsTire Pressure Pneumatic Tires AugerKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpTo Engage Drive To Engage AugersOperating Tips Always observe safety rules when performing any maintenanceGeneral Recommendations If possible, remove snow immediately after it fallsMaking AdjustmentsShift Rod Drive ControlChute Bracket Adjustment Chute AssemblySee Figure Adjust skid shoes as follows Auger ControlReplacing Belts Maintaining Your Snow ThrowerLubrication Remove Loosen Auger BeltPulley Slot Drive BeltChanging Friction Wheel Rubber Using a 3/4 wrench, hold the hex shaftSecure with the cupped washer and hex bolt removed earlier Friction WheelOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesAdressez-vous au «Service après-vente» Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Carter d’engrenages moitié CG avec raccord graisse With or without grease fittingsStyle Page Part RÉF Pièce Description Ensemble de roue Description Roue Jante Roulement Wheel Assembly DescriptionRim For parts and/or accessories refer to customer support on Page Garantie cette de GarantiePas couvre ne limitée garantie Cette Com.mtdcanadaDépannage Solution Causes ProblèmeUse PropreAccompagne qui moteur du d’utilisation notice la dans Jours, 30 de plus pendant entreposé être doit moteur le Si’essieu de EntretienFrottement de Roue Poulie la De Fente Et commandes lesMoteur du Tout empêcher pour’enlevez ÉloignezTarière la de d’entraînement Courroie Boulon l’autre retirezRoues LubrificationVitesse de ment ’engrenageRéglages Vitesses de levier du Tige Des l’entraînement de Commande’essieu Support de’utilisation Conseils Général d’ordre RecommandationsNormale PendantREMARQUEtourner moteur le LaissezGoulotte la de dégagement de Outil ’huile et d’essence PleinsFaites Ne Goulotte la de Commande Roues des d’orientation CommandeGoulotte la de direction Fonctions 2 àSouffleuse la de Commandes Pneuma Bandages pneus des Pression Tarière la de CommandeTiques Pas Goulotte la de Installation Vitesses de levier du tige la de Installation«Réglages» Bien passe qu’il ce jusqu’à raccord le sur TapezGuidon du Montage Goulotte la de manivelle la de Montage’assemblage pour requis Articles Cisaillement de BoulonsResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre ’essence de ManipulationMachine la d’utiliser Sécurité de SymbolesVente-après service au d’abord adresser vous sans Vente-après ServiceModèle de numéro le trouver Pour Matières des Table04103-769 4J1 N2G Ontario KITCHENER, South, Street Ottawa