Cub Cadet OEM-390-679 Lamp Wiring, Drift Cutters If Equipped, Clean-Out Tool, Final Adjustments

Page 8

3

Setting Up

Your Snow

Thrower

WARNING

Never use your hands to clean snow and ice from the chute assembly or auger housing.

IMPORTANT

Under any circum- stance do not exceed manufacturer’s recom- mended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.

Lamp Wiring

•Wrap the wire from the head lamp down the right handle until the wire can be plugged into the alterna- tor lead wire under the fuel tank. See Figure 3-8.

Alternator Lead

Alternator

Lead

Lamp Wire

NOTE: Wheels are omitted from illustration for clarity.

Figure 3-8

Figure 3-9

Clean-Out

Tool

Figure 3-10

Drift Cutters (If Equipped)

Drift cutters should be used when operating the snow thrower in heavy drift conditions.

•On models so equipped, drift cutters and hardware are assembled to the auger housing inverted.

•Remove the carriage bolts and wingnuts securing the drift cutters to the housing.

•Reposition drift cutters so they face forward as shown in Figure 3-9. Secure with hardware previously removed, wingnuts should be fastened on the outside of the housing as shown.

If your unit is not equipped with drift cutters, you may contact Customer Support as instructed on page 2 for information regarding price and availability.

Snowthrower Model

Drift Cutter Kit:

All models

OEM-390-679

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger housing and is designed to clear a clogged chute. See Figure 3-10. Refer to the Operation section for more detailed information regarding the chute clean-out tool.

NOTE: This item is fastened with a cable tie to the rear of the auger housing at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing.

Final Adjustments

Make these final adjustments before operating your snow thrower for the first time. Failure to follow these instruc- tions may cause damage to the snow thrower.

Wheel Drive Control & Shift Lever

Perform the following test to determine need for adjust- ment:

•Move the shift lever into sixth (6) position. See Figure

4-1.

•With the drive control released (see Figure 3-11A), push the snow thrower forward, then pull it back. The machine should move freely.

•Engage the drive control and attempt to move the machine both forward and back, resistance should be felt.

•Move the shift lever into the fast reverse (R2) position and repeat the previous two steps.

If you experienced resistance rolling the unit, either when repositioning the shift lever from 6 to R2 or when attempting to move the machine with the drive control released, adjust the drive control immediately. To adjust, proceed as follows:

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 28, 30, 33 & 45Two-Stage Snow Throwers Ottawa Street South, KITCHENER, Ontario N2G 4J1769-04103 06/10/08Customer Support Table of ContentsFinding and Recording Model Number Safety Symbols There are rotating blades insideDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Items Required For AssemblyLoose Parts Assembling HandleAttaching the Chute Assembly Attaching the Shift RodLamp Wiring Clean-Out ToolFinal Adjustments Drift Cutters If EquippedCheck the adjustment of the auger control as follows Skid ShoesTire Pressure Pneumatic Tires AugerOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Stopping The EngineTo Engage Drive To Engage AugersAlways observe safety rules when performing any maintenance Operating TipsGeneral Recommendations If possible, remove snow immediately after it fallsAdjustments MakingShift Rod Drive ControlChute Assembly Chute Bracket AdjustmentSee Figure Adjust skid shoes as follows Auger ControlReplacing Belts Maintaining Your Snow ThrowerLubrication Auger Belt Remove LoosenDrive Belt Pulley SlotUsing a 3/4 wrench, hold the hex shaft Changing Friction Wheel RubberSecure with the cupped washer and hex bolt removed earlier Friction WheelOff-Season Storage Trouble Shooting Problem Cause RemedyWarranty 05.28.08For parts and/or accessories refer to customer support on 6919 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesAdressez-vous au «Service après-vente» 305-342 cc Torque to 21 ft./lbs. maximum618-04514 Worm Gear Box Ass’y w/ grease fitting With or without grease fittings Carter d’engrenages moitié CG avec raccord graisseStyle Page Part RÉF Pièce Description Ensemble de roue Description Roue Jante Roulement Wheel Assembly DescriptionRim For parts and/or accessories refer to customer support on Page Garantie Garantie cette dePas couvre ne limitée garantie Cette Com.mtdcanadaSolution Causes Problème DépannagePropre UseAccompagne qui moteur du d’utilisation notice la dans Jours, 30 de plus pendant entreposé être doit moteur le Si’essieu de EntretienFrottement de Roue Et commandes les Poulie la De FenteMoteur du Tout empêcher pourÉloignez ’enlevezTarière la de d’entraînement Courroie Boulon l’autre retirezLubrification RouesVitesse de ment ’engrenageRéglages Des l’entraînement de Commande Vitesses de levier du Tige’essieu Support deGénéral d’ordre Recommandations ’utilisation ConseilsNormale PendantREMARQUEtourner moteur le LaissezGoulotte la de dégagement de Outil ’huile et d’essence PleinsFaites Ne Roues des d’orientation Commande Goulotte la de CommandeGoulotte la de direction Fonctions 2 àSouffleuse la de Commandes Pneuma Bandages pneus des Pression Tarière la de CommandeTiques Pas Vitesses de levier du tige la de Installation Goulotte la de Installation«Réglages» Bien passe qu’il ce jusqu’à raccord le sur TapezGoulotte la de manivelle la de Montage Guidon du Montage’assemblage pour requis Articles Cisaillement de BoulonsRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation FormationVotre ’essence de ManipulationSécurité de Symboles Machine la d’utiliserVente-après Service Vente-après service au d’abord adresser vous sansModèle de numéro le trouver Pour Matières des Table4J1 N2G Ontario KITCHENER, South, Street Ottawa 04103-769
Top Page Image Contents