Cub Cadet 724WE manual Operating Tips, Chute Assembly Adjustment, Auger Control Adjustment

Page 11

Operating Tips

NOTE: Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

WARNING: Muffler, engine and surrounding areas become hot and can cause a burn. Do not touch.

Set the skid shoes 1/4" below the shave plate for

normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.

Remove snow immediately after it falls.

Discharge snow downwind whenever possible.

Slightly overlap each previous cleared path.

Follow the precautions found under the heading To Stop Engine to prevent possible freeze-up.

Clean the snow thrower thoroughly after each use.

SECTION 6: MAKING ADJUSTMENTS

WARNING: Never attempt to make any adjustments while the engine is running, except where specified in operator’s manual.

Chute Assembly Adjustment

The distance snow is thrown can be varied by adjusting the pitch of the chute assembly. Refer to Chute Tilt Control in Section 4 of this manual.

Chute Directional Control

Support Bracket Adjustment

If the spiral at the base of the chute directional control isn’t fully engaging with the notches in the lower chute assembly, the support bracket can be adjusted inward or outward as follows:

Loosen, but do NOT remove the two hex nuts which secure the chute directional control support bracket to the snow thrower housing. See Figure 9.

 

Spiral

Hex Nuts

Support Bracket

 

 

Figure 9

Adjust the support bracket inward or outward so that the spiral is fully engaged in the notches on the chute before retightening the hex nuts.

Auger Control Adjustment

Refer to the information found under the heading Final Adjustments in Section 3 of this manual to adjust the auger control.

Traction Control Adjustment

Refer to the information found under the heading Final Adjustments in Section 3 of this manual to adjust the traction control. If you are uncertain that you have reached the correct adjustment, proceed as follows:

Tip the snow thrower forward, allowing it to rest on the auger housing.

Remove the frame cover underneath the snow thrower by removing six self-tapping screws.

With the traction control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever.

With the traction control engaged, the friction wheel must contact the drive plate. See Figure 10.

Friction

Wheel

Gear Shaft

Drive

Plate

Skid Shoe Adjustment

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes. Refer to Skid Shoe Adjustment in Section 3 of this manual.

Figure 10

If adjustment is necessary:

Loosen the jam nut on the traction drive cable and thread the cable in or out as necessary.

11

Image 11
Contents Operator’s Manual Table of Contents Operation Important Safe Operation PracticesTraining PreparationYour Responsibility Maintenance And StorageAssembling Your Snow Thrower Loose PartsTire Pressure Adjustment Final AdjustmentsAuger Control Adjustment Skid Shoe AdjustmentAuger Control Know Your Snow ThrowerHeadlight Shift LeverOperating Your Snow Thrower Recoil Starter To Stop EngineTire Chains Optional Equipment To Engage DriveTo Engage Augers Traction Control Adjustment Chute Assembly AdjustmentChute Directional Control Support Bracket Adjustment Auger Control AdjustmentLubrication Shift Rod AdjustmentMaintaining Your Snow Thrower Drive WheelsAuger Shaft Traction Control / Auger Control LockGear Shaft WheelsShave Plate and Skid Shoes ServiceBelt Removal And Replacement EngineDrive Belt Servicing Friction Wheel RubberHex Nut Bell Washer Part Description 724 WEModel 724 WE 784-5687A 784-5630A 12 -5689A Model 724WE 784-5632A 710-0459A 11 a 15 -0039C 21 -1379C Model 724 WE Model 724 WE For ground wire Light ass’y Chute Tilt Handle Halogen Light Harness Model 724 WE Page MANUFACTURER’S Limited Warranty for

724WE specifications

The Cub Cadet 724WE stands out as a premium snow blower, designed to handle heavy snowfall with ease. Equipped with a powerful 243cc OHV engine, this machine delivers efficient performance, ensuring that even the most stubborn snow can be cleared away effectively. The engine provides consistent power and reliability, making it an ideal choice for homeowners who face harsh winter conditions.

One of the key features of the Cub Cadet 724WE is its innovative, track-driven design. This unique system offers enhanced stability and maneuverability, allowing users to navigate through deep snow and over uneven surfaces without losing control. The tracked design helps maintain traction, making it easier to push through heavy accumulations of snow.

The 724WE also boasts a wide 24-inch clearing width and a high 21-inch intake height, allowing it to tackle large areas in less time. This means fewer passes and more time saved during snow removal operations. Additionally, the machine is equipped with a steel auger that ensures effective snow collection and a strong impeller for efficient discharge.

Another notable feature of the Cub Cadet 724WE is its adjustable chute. The 2-way joystick control allows for easy direction adjustments, letting users throw snow up to 40 feet away, while also providing the flexibility to control the angle of the chute. This ensures that snow can be directed precisely where needed, preventing it from piling up in unwanted areas.

For added convenience, the 724WE includes LED headlights that enhance visibility during nighttime and early morning snow-clearing tasks. This feature allows users to work safely in low-light conditions.

User comfort is also a priority with the Cub Cadet 724WE. The machine features ergonomic hand grips and a padded handle, reducing user fatigue during operation. The electric start capability simplifies the startup process, enabling users to start their snow blower with the push of a button, even in frigid temperatures.

In summary, the Cub Cadet 724WE is a robust snow blower equipped with advanced features and technologies that make winter clearing tasks more manageable and efficient. Its power, track-driven stability, and user-friendly design make it a worthy investment for anyone looking to conquer winter's worst. With its high performance and innovative features, the 724WE ensures that your driveway and walkways stay clear all season long.