Cub Cadet 724WE manual Operating Your Snow Thrower

Page 8

Chute Directional Control

The chute directional control is located on left side of the snow thrower.

To change the direction in which snow is thrown, turn chute directional control as follows:

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

Chute Tilt Control

The distance snow is thrown can be varied by adjusting the pitch of the chute assembly. Move the chute tilt control forward to decrease the distance, or toward the rear to increase the distance.

Fuel Shut-off Valve (if so equipped)

The fuel shut-off valve, located

 

 

under fuel tank, controls fuel flow

Closed

from the tank. Always make certain

 

it is in the Open (vertical) position

Open

before attempting to start the

engine.

 

 

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine.

Primer

Choke

 

 

Rope

Ignition Key

 

Starter

Throttle

Handle

 

 

 

 

Control

 

Figure 8

Ignition Key

The ignition key must be fully inserted in the switch before the unit will start. Remove the ignition key when snow thrower is not in use.

IMPORTANT: Do NOT attempt to turn the key.

SECTION 5: OPERATING YOUR SNOW THROWER

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Gas And Oil Fill-up

•Check oil level and add oil if necessary. Service the engine with gasoline as instructed in the separate engine manual packed with your snow thrower.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

To Start Engine

•Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

•Make certain the fuel cut-off valve, if your snow thrower is so equipped, is in the OPEN position.

•Make certain the auger and drive clutch levers are in the disengaged (released) position.

•Move throttle control up to FAST position. Insert the ignition key into slot. Make sure it snaps into place. Do NOT turn the key.

NOTE: Engine will not start unless the ignition key is inserted into the ignition slot .

Electric Starter

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

•Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

IMPORTANT: If your house wiring system is not a three- wire grounded system, do NOT use this electric starter under any conditions. Use the recoil starter instead.

IMPORTANT: If your home electrical system is

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingPreparation OperationMaintenance And Storage Your ResponsibilityLoose Parts Assembling Your Snow ThrowerFinal Adjustments Auger Control AdjustmentSkid Shoe Adjustment Tire Pressure AdjustmentKnow Your Snow Thrower HeadlightShift Lever Auger ControlOperating Your Snow Thrower To Stop Engine Recoil StarterTire Chains Optional Equipment To Engage DriveTo Engage Augers Chute Assembly Adjustment Chute Directional Control Support Bracket AdjustmentAuger Control Adjustment Traction Control AdjustmentShift Rod Adjustment Maintaining Your Snow ThrowerDrive Wheels LubricationTraction Control / Auger Control Lock Gear ShaftWheels Auger ShaftService Belt Removal And ReplacementEngine Shave Plate and Skid ShoesServicing Friction Wheel Rubber Drive BeltHex Nut Bell Washer 724 WE Part DescriptionModel 724 WE 784-5687A 784-5630A 12 -5689A Model 724WE 784-5632A 710-0459A 11 a 15 -0039C 21 -1379C Model 724 WE Model 724 WE For ground wire Light ass’y Chute Tilt Handle Halogen Light Harness Model 724 WE Page MANUFACTURER’S Limited Warranty for

724WE specifications

The Cub Cadet 724WE stands out as a premium snow blower, designed to handle heavy snowfall with ease. Equipped with a powerful 243cc OHV engine, this machine delivers efficient performance, ensuring that even the most stubborn snow can be cleared away effectively. The engine provides consistent power and reliability, making it an ideal choice for homeowners who face harsh winter conditions.

One of the key features of the Cub Cadet 724WE is its innovative, track-driven design. This unique system offers enhanced stability and maneuverability, allowing users to navigate through deep snow and over uneven surfaces without losing control. The tracked design helps maintain traction, making it easier to push through heavy accumulations of snow.

The 724WE also boasts a wide 24-inch clearing width and a high 21-inch intake height, allowing it to tackle large areas in less time. This means fewer passes and more time saved during snow removal operations. Additionally, the machine is equipped with a steel auger that ensures effective snow collection and a strong impeller for efficient discharge.

Another notable feature of the Cub Cadet 724WE is its adjustable chute. The 2-way joystick control allows for easy direction adjustments, letting users throw snow up to 40 feet away, while also providing the flexibility to control the angle of the chute. This ensures that snow can be directed precisely where needed, preventing it from piling up in unwanted areas.

For added convenience, the 724WE includes LED headlights that enhance visibility during nighttime and early morning snow-clearing tasks. This feature allows users to work safely in low-light conditions.

User comfort is also a priority with the Cub Cadet 724WE. The machine features ergonomic hand grips and a padded handle, reducing user fatigue during operation. The electric start capability simplifies the startup process, enabling users to start their snow blower with the push of a button, even in frigid temperatures.

In summary, the Cub Cadet 724WE is a robust snow blower equipped with advanced features and technologies that make winter clearing tasks more manageable and efficient. Its power, track-driven stability, and user-friendly design make it a worthy investment for anyone looking to conquer winter's worst. With its high performance and innovative features, the 724WE ensures that your driveway and walkways stay clear all season long.
Top Page Image Contents