Cub Cadet 724WE manual Service, Engine, Shave Plate and Skid Shoes, Belt Removal And Replacement

Page 14

SECTION 8: SERVICE

WARNING: Before servicing, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.

Engine

Refer to the separate engine manual packed with your unit for all engine related maintenance procedures.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove the skid shoes, proceed as follows:

•Remove the six carriage bolts, bell washers and hex nuts which attach them to the snow thrower.

•Reassemble new skid shoes with the six carriage bolts, bell washers (cupped side goes against skid shoes) and hex nuts. Make certain the skid shoes are adjusted to be level.

To remove shave plate, remove the carriage bolts, belleville washers and hex nuts which attach it to the snow thrower housing. Reassemble new shave plate, making sure heads of the carriage bolts are to the inside of the housing. Tighten securely.

Belt Removal And Replacement

WARNING: Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Drain fuel into an approved container or place a piece of plastic film underneath the gas cap to prevent gasoline from leaking.

Auger Belt

•Remove the plastic belt cover by removing the two self-tapping screws. See Figure 17.

•Drain the gasoline from the snow thrower.

•Tip the snow thrower forward so that it rests on its auger housing and remove six self-tapping screws from the frame cover underneath the snow thrower.

•Roll the belt off the engine pulley. See Figure 18.

•Unhook the idler spring from the hex bolt on the auger housing. See Figure 19.

Belt

Cover

Self-Tapping Screws

Figure 17

 

Drive

Auger Pulley

Belt

Engine

Pulley

Auger

Belt

Engine

Pulley

Idler

Idler

Pulley

Pulley

 

Figure 18

Friction Wheel

Frame

Support

Bracket

Auger Belt

Auger

Idler

Support

Spring

Bracket

Pulley

 

 

Auger Spring

 

 

 

 

Housing

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual Table of Contents Preparation Important Safe Operation PracticesTraining OperationMaintenance And Storage Your ResponsibilityLoose Parts Assembling Your Snow ThrowerSkid Shoe Adjustment Final AdjustmentsAuger Control Adjustment Tire Pressure AdjustmentShift Lever Know Your Snow ThrowerHeadlight Auger ControlOperating Your Snow Thrower To Stop Engine Recoil StarterTire Chains Optional Equipment To Engage DriveTo Engage Augers Auger Control Adjustment Chute Assembly AdjustmentChute Directional Control Support Bracket Adjustment Traction Control AdjustmentDrive Wheels Shift Rod AdjustmentMaintaining Your Snow Thrower LubricationWheels Traction Control / Auger Control LockGear Shaft Auger ShaftEngine ServiceBelt Removal And Replacement Shave Plate and Skid ShoesServicing Friction Wheel Rubber Drive BeltHex Nut Bell Washer 724 WE Part DescriptionModel 724 WE 784-5687A 784-5630A 12 -5689A Model 724WE 784-5632A 710-0459A 11 a 15 -0039C 21 -1379C Model 724 WE Model 724 WE For ground wire Light ass’y Chute Tilt Handle Halogen Light Harness Model 724 WE Page MANUFACTURER’S Limited Warranty for

724WE specifications

The Cub Cadet 724WE stands out as a premium snow blower, designed to handle heavy snowfall with ease. Equipped with a powerful 243cc OHV engine, this machine delivers efficient performance, ensuring that even the most stubborn snow can be cleared away effectively. The engine provides consistent power and reliability, making it an ideal choice for homeowners who face harsh winter conditions.

One of the key features of the Cub Cadet 724WE is its innovative, track-driven design. This unique system offers enhanced stability and maneuverability, allowing users to navigate through deep snow and over uneven surfaces without losing control. The tracked design helps maintain traction, making it easier to push through heavy accumulations of snow.

The 724WE also boasts a wide 24-inch clearing width and a high 21-inch intake height, allowing it to tackle large areas in less time. This means fewer passes and more time saved during snow removal operations. Additionally, the machine is equipped with a steel auger that ensures effective snow collection and a strong impeller for efficient discharge.

Another notable feature of the Cub Cadet 724WE is its adjustable chute. The 2-way joystick control allows for easy direction adjustments, letting users throw snow up to 40 feet away, while also providing the flexibility to control the angle of the chute. This ensures that snow can be directed precisely where needed, preventing it from piling up in unwanted areas.

For added convenience, the 724WE includes LED headlights that enhance visibility during nighttime and early morning snow-clearing tasks. This feature allows users to work safely in low-light conditions.

User comfort is also a priority with the Cub Cadet 724WE. The machine features ergonomic hand grips and a padded handle, reducing user fatigue during operation. The electric start capability simplifies the startup process, enabling users to start their snow blower with the push of a button, even in frigid temperatures.

In summary, the Cub Cadet 724WE is a robust snow blower equipped with advanced features and technologies that make winter clearing tasks more manageable and efficient. Its power, track-driven stability, and user-friendly design make it a worthy investment for anyone looking to conquer winter's worst. With its high performance and innovative features, the 724WE ensures that your driveway and walkways stay clear all season long.
Top Page Image Contents