Cub Cadet 1130 SWE manual Maintenance And Storage

Page 4

3.The clutch levers must operate easily in both directions and automatically return to the disengaged position when released.

4.Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.

5.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

6.Do not operate machine while under the influence of alcohol or drugs.

7.Muffler and engine become hot and can cause a burn. Do not touch.

8.Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic.

9.Exercise caution when changing direction and while operating on slopes.

10.Plan your snow throwing pattern to avoid discharge towards windows, walls, cars etc. To avoid property damage or personal injury caused by a ricochet.

11.Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.

12.Do not overload machine capacity by attempting to clear snow at too fast of a rate.

13.Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.

14.Disengage power to the auger/impeller when transporting or not in use.

15.Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when in reverse.

16.If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating.

17.Disengage all clutch levers and stop engine before you leave the operating position (behind the handles). Wait until the auger/impeller comes to a complete stop before unclogging the discharge chute, making any adjustments, or inspections.

18.Never put your hand in the discharge or collector openings. Always use a clearing tool to unclog the discharge opening.

19.Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20.If situations occur which are not covered in this manual,

use care and good judgment. Contact your dealer or telephone 1-800-528-1009 for assistance and the name of your nearest servicing dealer.

Maintenance And Storage

1.Never tamper with safety devices. Check their proper operation regularly.

2.Disengage all clutch levers and stop engine. Wait until the auger/impeller come to a complete stop. Disconnect the spark plug wire and ground against the engine to prevent unintended starting before cleaning, repairing, or inspecting.

3.Check bolts, and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage.

4.Do not change the engine governor setting or over-speed the engine. The governor controls the maximum safe operating speed of the engine.

5.Snow thrower shave plates and skid shoes are subject to wear and damage. For your safety protection, frequently check all components and replace with original equipment manufacturer’s (O.E.M.) parts only. Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety.

6.Check clutch controls periodically to verify they engage and disengage properly and adjust, if necessary. Refer to the adjustment section in this operator’s manual for instructions.

7.Maintain or replace safety and instruction labels, as necessary.

8.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

9.Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of auger/impeller.

10.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace ,clothes dryer etc.

11.Always refer to the operator’s manual for proper instructions on off-season storage.

WARNING: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents OPERATOR’S Manual Table of Contents Important Safe Operation Practices TrainingPreparation OperationMaintenance And Storage Assembly Assembling Your Snow ThrowerUnpacking Loose PartsFinal Adjustments Auger Control AdjustmentSkid Shoe Adjustment Traction Control and Shift Lever AdjustmentKnow Your Snow Thrower Chute Tilt ControlAuger Drive Control Skid ShoeOperating Your Snow Thrower Recoil Starter To Stop EngineTo Engage Wheel Drive To Engage AugersTraction Control Adjustment Chute Assembly AdjustmentShift Rod Adjustment Skid Shoe Adjustment Auger Control AdjustmentMaintaining Your Snow Thrower LubricationBelt Removal And Replacement Servicing Your Snow ThrowerEngine AugersReplacing Friction Wheel Rubber Drive BeltOff-season Storage Trouble Shooting Problem Cause RemedyPage Models 826 SWE & 1130 SWE Part DescriptionFor Reference Only 746-0901 Control Cable Models 826 SWE & 1130 SWE 712-0798 Hex Nut 3/8-16 Models 826 SWE & 1130 SWE 734-1712 Drive Clutch Cable Routed Below Axle Hooked Here Dogg Assembly RH Dogg Assembly LH 618-0575 Page Page MANUFACTURER’S Limited Warranty for

1130 SWE specifications

The Cub Cadet 1130 SWE is a robust snow blower designed for homeowners who need reliable performance during the winter months. With a focus on power, efficiency, and user comfort, this machine stands out in the crowded market of snow removal equipment.

One of the main features of the Cub Cadet 1130 SWE is its powerful 420cc, 4-cycle OHV engine, which delivers exceptional snow clearing capability. This engine provides the necessary strength to tackle heavy snowfall and ice, making it ideal for areas that experience substantial winter weather. With a clearing width of 30 inches and a throwing distance of up to 40 feet, this snow blower is capable of covering large areas quickly and efficiently.

The Cub Cadet 1130 SWE is designed with a hydrostatic drive system that allows for seamless speed adjustments. This innovative technology enables users to maintain precise control over the speed of the snow blower, ensuring optimal performance on various terrains and snow conditions. Whether dealing with light powder or heavy wet snow, operators can find the perfect pace to get the job done.

Ergonomic design plays a significant role in the usability of the 1130 SWE. The height-adjustable handle with comfort grips ensures that users can operate the machine comfortably for extended periods. Moreover, the machine features an electric start option, making it easy to ignite the engine in cold weather without the hassle of manual starting.

Another notable characteristic of this snow blower is its heavy-duty steel auger and impeller. These components work together to break up and eliminate snow efficiently, contributing to its effectiveness in tough conditions. Additionally, the adjustable skid shoes allow users to control the height of the auger, making it easier to clear snow without damaging surfaces such as driveways and sidewalks.

For enhanced visibility during night-time operations, the Cub Cadet 1130 SWE is equipped with integrated LED headlights. This feature ensures that operators can see their path clearly, reducing the risk of accidents in low-light conditions.

In summary, the Cub Cadet 1130 SWE is a powerful snow blower that combines performance, user-friendly features, and innovative technology. Whether facing heavy snowfalls or light flurries, this snow blower is a reliable partner for homeowners looking to maintain their properties during the winter season.
Top Page Image Contents