Cub Cadet 1130 SWE manual Recoil Starter, To Stop Engine, To Engage Wheel Drive, To Engage Augers

Page 9

WARNING: The electric starter is equipped with a grounded three-wire power cord and plug and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

•If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

•If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before using the electric starter.

•If you have a grounded three-prong receptacle, proceed as follows:

•Rotate choke knob to OFF position and do not prime engine.

•Connect power cord to switch box on engine. Plug the other end of power cord into a three-hole, grounded 120 volt AC receptacle.

•Push starter button on top of the engine to crank engine. As you crank the engine, move choke knob to FULL choke position.

•When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF.

•When disconnecting the power cord, always unplug from the three-prong receptacle first and then from the snow thrower.

Recoil Starter

•Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.

•Push primer button two or three times. If engine is warm, push primer button once only.

NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15°F.

•Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.

•Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.

•Repeat the previous steps until engine starts.

To Stop Engine

•Run engine for a few minutes before stopping to help dry off any moisture on the engine.

•To help prevent possible freeze-up of starter, proceed as follows.

Electric Starter:

•Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.

Recoil Starter

•With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.

•Move throttle control to “stop” or “off” position.

•Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

NOTE: Keep it in a safe place. Engine will not start without ignition key.

Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

To Engage Wheel Drive

•With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

NOTE: Use slower speeds in higher snow, and until you are familiar with the operation of the snow thrower.

•Squeeze the traction control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

IMPORTANT: NEVER move the shift lever without first releasing the traction control. Doing so will cause premature wear to the drive system’s friction wheel.

To Engage Augers

To engage the augers and start the snow throwing action, proceed as follows:

•Squeeze the auger control against the left handle. To disengage power to the augers:

•Release both the auger control and the traction control, if engaged.

The auger control can be locked so you can turn the electric chute directional control without interrupting the snow throwing process.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents OPERATOR’S Manual Table of Contents Training Important Safe Operation PracticesPreparation OperationMaintenance And Storage Assembling Your Snow Thrower AssemblyUnpacking Loose PartsAuger Control Adjustment Final AdjustmentsSkid Shoe Adjustment Traction Control and Shift Lever AdjustmentChute Tilt Control Know Your Snow ThrowerAuger Drive Control Skid ShoeOperating Your Snow Thrower To Stop Engine Recoil StarterTo Engage Wheel Drive To Engage AugersChute Assembly Adjustment Traction Control AdjustmentShift Rod Adjustment Auger Control Adjustment Skid Shoe AdjustmentMaintaining Your Snow Thrower LubricationServicing Your Snow Thrower Belt Removal And ReplacementEngine AugersDrive Belt Replacing Friction Wheel RubberOff-season Storage Problem Cause Remedy Trouble ShootingPage Part Description Models 826 SWE & 1130 SWEFor Reference Only 746-0901 Control Cable Models 826 SWE & 1130 SWE 712-0798 Hex Nut 3/8-16 Models 826 SWE & 1130 SWE 734-1712 Drive Clutch Cable Routed Below Axle Hooked Here Dogg Assembly RH Dogg Assembly LH 618-0575 Page Page MANUFACTURER’S Limited Warranty for

1130 SWE specifications

The Cub Cadet 1130 SWE is a robust snow blower designed for homeowners who need reliable performance during the winter months. With a focus on power, efficiency, and user comfort, this machine stands out in the crowded market of snow removal equipment.

One of the main features of the Cub Cadet 1130 SWE is its powerful 420cc, 4-cycle OHV engine, which delivers exceptional snow clearing capability. This engine provides the necessary strength to tackle heavy snowfall and ice, making it ideal for areas that experience substantial winter weather. With a clearing width of 30 inches and a throwing distance of up to 40 feet, this snow blower is capable of covering large areas quickly and efficiently.

The Cub Cadet 1130 SWE is designed with a hydrostatic drive system that allows for seamless speed adjustments. This innovative technology enables users to maintain precise control over the speed of the snow blower, ensuring optimal performance on various terrains and snow conditions. Whether dealing with light powder or heavy wet snow, operators can find the perfect pace to get the job done.

Ergonomic design plays a significant role in the usability of the 1130 SWE. The height-adjustable handle with comfort grips ensures that users can operate the machine comfortably for extended periods. Moreover, the machine features an electric start option, making it easy to ignite the engine in cold weather without the hassle of manual starting.

Another notable characteristic of this snow blower is its heavy-duty steel auger and impeller. These components work together to break up and eliminate snow efficiently, contributing to its effectiveness in tough conditions. Additionally, the adjustable skid shoes allow users to control the height of the auger, making it easier to clear snow without damaging surfaces such as driveways and sidewalks.

For enhanced visibility during night-time operations, the Cub Cadet 1130 SWE is equipped with integrated LED headlights. This feature ensures that operators can see their path clearly, reducing the risk of accidents in low-light conditions.

In summary, the Cub Cadet 1130 SWE is a powerful snow blower that combines performance, user-friendly features, and innovative technology. Whether facing heavy snowfalls or light flurries, this snow blower is a reliable partner for homeowners looking to maintain their properties during the winter season.
Top Page Image Contents