Cub Cadet 1130 SWE manual Trouble Shooting, Problem Cause Remedy

Page 15

SECTION 8: TROUBLE SHOOTING

Problem

 

Cause

 

Remedy

 

 

 

 

 

Engine fails to start

1.

Fuel tank empty, or stale fuel.

1.

Fill tank with fresh gasoline.

 

2.

Blocked fuel line.

2.

Clean the fuel line.

 

3.

Choke not in ON position

3.

Move switch to ON position

 

4.

Faulty spark plug.

4.

Clean, adjust gap or replace.

 

5.

Safety key not in ignition switch on engine.

5.

Insert the key fully into the switch.

 

6.

Spark plug wire disconnected.

6.

Connect spark plug wire.

 

7.

Primer button not being used properly.

7.

Refer to the engine manual.

 

8.

Fuel shut-off valve closed.

8.

Open fuel shut-off valve.

Engine runs erratic

1.

Unit running on CHOKE.

1.

Move choke lever to OFF position.

 

2.

Blocked fuel line or stale fuel.

2.

Clean fuel line; fill tank with clean, fresh

 

 

 

 

gasoline.

 

3.

Water or dirt in fuel system.

3.

Drain fuel tank and carburetor. Refill with

 

 

 

 

fresh fuel.

 

4.

Carburetor out of adjustment.

4.

Refer to the engine manual.

Loss of power

1.

Spark plug wire loose.

1.

Connect and tighten spark plug wire.

 

2.

Gas cap vent hole plugged.

2.

Remove ice and snow from gas cap. Be

 

 

 

 

certain vent hole is clear.

 

3.

Exhaust port plugged.

3.

Refer to the engine manual.

Engine overheats

1.

Carburetor not adjusted properly.

1.

Refer to the engine manual or have the

 

 

 

 

carburetor adjusted by an authorized

 

 

 

 

engine service dealer.

Excessive vibration

1.

Loose parts or damaged auger.

1.

Stop engine immediately and disconnect

 

 

 

 

spark plug wire. Tighten all bolts and nuts. If

 

 

 

 

vibration continues, have unit serviced by

 

 

 

 

an authorized service dealer.

Unit fails

1.

Traction control cable in need of adjustment.

1.

Adjust traction control cable. Refer to

to propel itself

 

 

 

Adjustment Section.

 

2.

Drive belt loose or damaged.

2.

Replace drive belt. Refer to Servicing

 

 

 

 

Section.

Unit fails

1.

Discharge chute clogged.

1.

Stop engine immediately and disconnect

to discharge snow

 

 

 

spark plug wire. Clean discharge chute and

 

 

 

 

inside of auger housing.

 

2.

Foreign object lodged in auger.

2.

Stop engine immediately and disconnect

 

 

 

 

spark plug wire. Remove object from auger.

 

3.

Auger control cable in need of adjustment.

3.

Refer to Final Adjustments in Assembly

 

 

 

 

Section.

 

4.

Auger belt loose or damaged.

4.

Refer to the Servicing Section.

 

5.

Shear bolt(s) sheared.

5.

Replace Shear bolt(s).

Electric chute fails to

1.

Loose electrical connections.

1.

Make sure all connections are tight and fully

turn

 

 

 

installed.

 

2.

Blown Fuse.

2.

Replace with #5A fuse. The fuse is under

 

 

 

 

handle panel near switch connector.

Electric chute turns in

1.

The switch connector is installed backwards

1.

Unplug the switch connector under the

opposite direction of

 

 

 

handle panel. Turn connector 180° and

the switch

 

 

 

reconnect.

Heated grips are not

1.

Loose electrical connections.

1.

Under the handle panel, check connections

creating heat

 

 

 

from the handles to the wiring harness.

 

2.

Blown fuse.

2.

Replace with #5A fuse. The fuse is under

 

 

 

 

handle panel near switch connector.

 

3.

Faulty grip. If one heated grip fails, both grips

3.

Have the grips checked at an authorized

 

 

will not function.

 

service dealer.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents OPERATOR’S Manual Table of Contents Operation Important Safe Operation PracticesTraining PreparationMaintenance And Storage Loose Parts AssemblyAssembling Your Snow Thrower UnpackingTraction Control and Shift Lever Adjustment Final AdjustmentsAuger Control Adjustment Skid Shoe AdjustmentSkid Shoe Know Your Snow ThrowerChute Tilt Control Auger Drive ControlOperating Your Snow Thrower To Engage Augers Recoil StarterTo Stop Engine To Engage Wheel DriveChute Assembly Adjustment Traction Control AdjustmentShift Rod Adjustment Lubrication Skid Shoe AdjustmentAuger Control Adjustment Maintaining Your Snow ThrowerAugers Belt Removal And ReplacementServicing Your Snow Thrower EngineDrive Belt Replacing Friction Wheel RubberOff-season Storage Problem Cause Remedy Trouble ShootingPage Part Description Models 826 SWE & 1130 SWEFor Reference Only 746-0901 Control Cable Models 826 SWE & 1130 SWE 712-0798 Hex Nut 3/8-16 Models 826 SWE & 1130 SWE 734-1712 Drive Clutch Cable Routed Below Axle Hooked Here Dogg Assembly RH Dogg Assembly LH 618-0575 Page Page MANUFACTURER’S Limited Warranty for

1130 SWE specifications

The Cub Cadet 1130 SWE is a robust snow blower designed for homeowners who need reliable performance during the winter months. With a focus on power, efficiency, and user comfort, this machine stands out in the crowded market of snow removal equipment.

One of the main features of the Cub Cadet 1130 SWE is its powerful 420cc, 4-cycle OHV engine, which delivers exceptional snow clearing capability. This engine provides the necessary strength to tackle heavy snowfall and ice, making it ideal for areas that experience substantial winter weather. With a clearing width of 30 inches and a throwing distance of up to 40 feet, this snow blower is capable of covering large areas quickly and efficiently.

The Cub Cadet 1130 SWE is designed with a hydrostatic drive system that allows for seamless speed adjustments. This innovative technology enables users to maintain precise control over the speed of the snow blower, ensuring optimal performance on various terrains and snow conditions. Whether dealing with light powder or heavy wet snow, operators can find the perfect pace to get the job done.

Ergonomic design plays a significant role in the usability of the 1130 SWE. The height-adjustable handle with comfort grips ensures that users can operate the machine comfortably for extended periods. Moreover, the machine features an electric start option, making it easy to ignite the engine in cold weather without the hassle of manual starting.

Another notable characteristic of this snow blower is its heavy-duty steel auger and impeller. These components work together to break up and eliminate snow efficiently, contributing to its effectiveness in tough conditions. Additionally, the adjustable skid shoes allow users to control the height of the auger, making it easier to clear snow without damaging surfaces such as driveways and sidewalks.

For enhanced visibility during night-time operations, the Cub Cadet 1130 SWE is equipped with integrated LED headlights. This feature ensures that operators can see their path clearly, reducing the risk of accidents in low-light conditions.

In summary, the Cub Cadet 1130 SWE is a powerful snow blower that combines performance, user-friendly features, and innovative technology. Whether facing heavy snowfalls or light flurries, this snow blower is a reliable partner for homeowners looking to maintain their properties during the winter season.
Top Page Image Contents