Cub Cadet 826 4x4 manual To Engage Drive, To Engage Augers, Operating Tips, Skid Shoe Adjustment

Page 10

•Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

NOTE: Keep it in a safe place. Engine will not start without ignition key.

Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

To Engage Drive

•With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

NOTE: Use slower speeds in higher snow and until you are familiar with the operation of the snow thrower.

•Squeeze the traction control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

IMPORTANT: NEVER move the shift lever without first releasing the traction control. Doing so will cause premature wear to the drive system’s friction wheel.

To Engage Augers

To engage the augers and start the snow throwing action, proceed as follows:

•Squeeze the auger control against the left handle. To disengage power to the augers:

•Release both the auger control and the traction control, if engaged.

The auger control can be locked so you can turn the electric chute directional control without interrupting the snow throwing process.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed

150°F. Avoid these areas.

•For the most efficient snow removal, remove snow immediately after it falls.

•Discharge the snow downwind whenever possible.

•Slightly overlap each previous path.

•Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.

•Be certain to follow the precautions found in the To Stop Engine section to prevent possible freeze-up.

•Clean the snow thrower thoroughly after each use.

SECTION 5: MAKING ADJUSTMENTS

WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Skid Shoe Adjustment

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes. Refer to Skid Shoe Adjustment in the Assembly Section.

Auger Control Adjustment

Refer to the information found under Final Adjustments in the Assembly Section to adjust the auger control.

Chute Assembly Adjustment

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Chute Tilt Control in the Know Your Snow Thrower Section.

Traction Control Adjustment

Refer to the information found under Final Adjustment

in the Assembly Section to adjust the traction control. If you are uncertain that you have reached the correct adjustment, proceed as follows:

WARNING: Drain the gasoline out of the snow thrower’s tank, or place a piece of plastic film under the gas cap to avoid spillage BEFORE making the adjustment.

•Tip the snow thrower forward, allowing it to rest on the auger housing.

•Remove the frame cover underneath the snow thrower by removing the six self-tapping screws.

•With the traction control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever.

•With the traction control engaged, the friction wheel

must contact the drive plate. See Figure 9. If adjustment is necessary:

•Loosen the jam nut on the traction drive cable. Adjust the cable as necessary. Refer to Figure 6.

•Retighten the jam nut to secure the cable when correct adjustment is reached.

•Reassemble the frame cover.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Table of Contents Preparation Important Safe Operation PracticesTraining OperationMaintenance And Storage Your ResponsibilityUnpacking AssemblyAssembling Your Snow Thrower Loose PartsTraction Control and Shift Lever Adjustment Final AdjustmentsAuger Control Adjustment Skid Shoe AdjustmentKnow Your Snow Thrower Tire PressureOperating Your Snow Thrower Recoil Starter To Start EngineElectric Starter To Stop EngineChute Assembly Adjustment Skid Shoe AdjustmentAuger Control Adjustment Traction Control AdjustmentMaintaining Your Snow Thrower Shift Rod AdjustmentLubrication Engine Belt Removal And ReplacementServicing Your Snow Thrower AugersDrive Belt Servicing Friction Wheel Rubber Off-season Storage Trouble Shooting Guide Trouble Possible Causes Corrective ActionModel DescriptionModel Description Model 22 -0473 Sprocket 714-0104 Cotter Pin 714-0474 716-0102 Model Model For Reference Only Part Description Page Page MANUFACTURER’S Limited Warranty for

826 4x4 specifications

The Cub Cadet 826 4x4 is a powerful and versatile snow blower designed for homeowners who face harsh winter conditions. It combines robust engineering with user-friendly features, making snow removal a more manageable task. This machine is equipped with a 26-inch clearing width, allowing it to tackle significant snow accumulations efficiently.

One of the standout features of the Cub Cadet 826 4x4 is its 4-wheel drive capability. This ensures that users can navigate snowy terrain with ease, providing enhanced traction and stability on slopes and uneven surfaces. The hydrostatic transmission allows for smooth speed adjustments and effortless maneuvering. This feature is particularly beneficial when operating in tight corners or delicate areas where precision is essential.

The snow blower is powered by a reliable 2-stage engine, which generates ample power for heavy-duty snow clearing. The two-stage system means that after the auger gathers snow, it is thrown out of the discharge chute with significant force, making it ideal for dealing with packed snow and deep drifts. The adjustable chute also allows users to direct the snow far away from the cleared area, preventing it from being blown back onto already cleared surfaces.

In terms of comfort, the Cub Cadet 826 4x4 prioritizes ease of use. It features heated hand grips that keep operators warm during extended periods of cold weather. Moreover, the large, easy-to-operate controls are designed to minimize fatigue, allowing users to focus on the job at hand. The machine’s generous fuel tank capacity ensures longer operation times without frequent refueling, adding to its convenience.

Durability is another key characteristic of the Cub Cadet 826 4x4. Built with high-grade materials, it is designed to withstand the rigors of winter use. The high-impact, snow-resistant construction ensures longevity, making it a smart investment for homeowners looking to manage snow effectively year after year.

In summary, the Cub Cadet 826 4x4 is an exceptional snow blower that combines power, technology, and user comfort. Its robust features make it suitable for tackling even the most challenging winter conditions, ensuring users can clear their paths quickly and efficiently. With its combination of durability, performance, and ease of use, the Cub Cadet 826 4x4 is a top choice for anyone looking to conquer snow this winter.
Top Page Image Contents