Operating Instructions

74” Allied Snowblower

1.Do not operate the blower in the fully raised position. The three-point hitch on some tractors raises high enough to cause the PTO shaft to bind.

This can cause damage to the PTO shaft and/or to the hitch and pins. ALERT: PTO shaft angle should not exceed 20 degrees for

optimum performance and life. Damage may occur to PTO and/or snowblower if angle becomes more extreme.

2.Depth of cut can be partially controlled by tilting the blower forward or

backward. Adjust the top link of the tractor hitch so the snowblower is just

slightly tilted back when resting on the ground. CAUTION: Excessive backward tilt may cause the "U" joints to flutter resulting in PTO shear bolt failure.

3.Adjust the lower link sway chains or blocks on the tractor to restrict side movement of the blower when operating.

4.Run the blower at low rpm to check operation before blowing snow.

5.The snowblower has two shear bolts to protect the tractor and blower in case a large object enters the blower. PTO shear bolt (Two 5/16" x 1"-Grade 5) Auger shear bolt (1/4" x 1"-Grade 5). Shear bolts should be fastened with a lock nut or two jam nuts. These bolts must be kept tight to prevent wear of the bolt and bolt holes.

6.Never run PTO shaft at over 600 rpm.

7.Chain tension: Slack on the lower side of the chain should be 3/8 to ½”.

8.Lubrication:

a)The spout clamps and rings should be periodically lubricated with gun grease.

b)PTO shaft universal joints and square shaft slide should be greased daily.

c)Regularly oiling the chain will significantly increase the life of the chain.

d)The grease fitting on the hydraulic spout swivel arm should be kept

lubricated.

9.Periodically check all bolts for tightness. The bolt holding on the

fan and the bearing bolts are of particular importance.

10. DANGER: Always stop blower for servicing or unplugging. The PTO should be disengaged before dismounting from the tractor.

11. CAUTION: Always check to see that both ends of the PTO shaft are securely attached as per instructions every time you are preparing to use the snowblower.

12.Shear Sprocket: The Shear Sprocket (#52) should be checked at the beginning of every season to make sure it will spin freely. With time this sprocket could corrode and seize which will not allow the shear bolt to break if something jams in the snowblower auger. Clean to loosen if necessary.

13.When replacing bearings or tightening a loose bearing collar, always tighten collar in the direction of shaft rotation using a center punch or a similar tool.

-3 -

FK331 specifications

The Buhler FK331 is a cutting-edge piece of machinery that has garnered attention in the field of food processing and grain milling. Known for its efficiency and reliability, the FK331 is equipped with several key features and technologies that enhance its operational capabilities.

One of the standout characteristics of the Buhler FK331 is its modular design, which allows for easy integration into existing production lines. Its compact structure makes it suitable for locations with spatial constraints while still offering robust performance. This flexibility is essential in modern industrial settings where adaptation to changing production needs is crucial.

The FK331 employs advanced milling technology that ensures optimal particle size distribution. This is particularly important in the production of fine flour, where consistency and quality are non-negotiable. The machine utilizes a state-of-the-art grinding system that allows for a high degree of customization, enabling operators to adjust settings according to specific product requirements.

Energy efficiency is another significant feature of the FK331. It is designed to minimize energy consumption while maintaining high output levels. This is achieved through the integration of intelligent drive systems, which monitor and control energy usage in real-time. Such innovations not only reduce operational costs but also make the FK331 an environmentally friendly option for grain milling.

User-friendliness is a core aspect of the Buhler FK331. The machine is equipped with intuitive controls and an easy-to-navigate interface, allowing operators to manage settings and monitor performance effortlessly. This ease of use reduces training times and minimizes the chances of operational errors.

Safety is also a top priority with the FK331. The machine features multiple safety mechanisms, including emergency shut-off systems and protective barriers, ensuring that operators can work in a secure environment.

In terms of maintenance, the Buhler FK331 is designed for easy access to all critical components, simplifying routine checks and repairs. This reduces downtime and helps maintain optimal operational efficiency over time.

Overall, the Buhler FK331 stands out as a versatile, efficient, and user-friendly machine in the grain milling industry. With its innovative design, advanced milling technology, energy efficiency features, and focus on safety and maintenance, it meets the demands of modern food processing and provides a reliable solution for high-quality output.