Craftsman 536.88155 operating instructions Check the OIL, Before Starting the Engine, Fill GAS

Page 13

,Foreaseofmaneuverabilityinlight

snow conditions, disconnect the kllck pin from the wheel locked position and push into the single wheel drive position (unlocked axle hole only). See Figure 12.

K]ick Pin

Position

D_ive

Unlocked

Single Wheel

 

Figure 12

NOTE: Make sure that the Idiok pin is in the single wheel drive position of the axle only and not through the locked position.

BEFORE STARTING THE ENGINE

1.Before you service or start the en-

gine, familiarize yourseff with the snow thrower. Be sure you under- stand the function and location of all

controls.

2.Check the tension of clutch cable before starting the engine. See To

Adjust The Control Cable para-

graph in the Service & Adjust- merits section of this manual.

3.Be sure that all fasteners are tight.

4.Make sure the height adjust skids are pmpedy adjusted. See To Ad- just Skid Height paragraph in the Service & Adjustments section of this manual.

5.Checktire pressure (14-17 pounds). Do not exceed maximum amount of pressure.

CHECK THE OIL:

NOTE: The engine was shipped from the fectoPJfilled with oil. Check the lev- el of the oil. Add oil as needed.

To Add Oil

1. Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Remove the oil fill cab/dipstick and wipe with a clean cloth.

3.Insert the oil fill cab/dipstick and turn clockwise to tighten.

4.Remove the oN fill cab/dipstick and check the oil

5.If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick (see F_ure 13). Do not add too much oil.

%

NOTE: OII level must be at the Full mad(

Figure 13

6.Tighten the fill cap/dipstick securely each time you check the oil level.

NOTE; Synthetic oil can assist with starting in extreme cold temperatures. Synthetic 5W30 is acceptable for all temperatures. DO NOT mix o=1with gasoline.

FILL GAS:

This engine is certified to operate on gasoline. Exhaust Emission Control System: EM (Engine Modifications).

4_b WARNING: Alcohol blended fuels (eelied gasohol or those using ethanol or

methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel sys- tem of an engine while in storage.

NOTE; To avoid engine problems, the fuel system must be emptied before storage for 30 days or longer. Start the engine and let it run until the fuel lines and carburetor are empty. Use fresh

fuel next season. See the Storage section in this manual for additional ino

formation.

F-0410111L13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents OperatorsManual Snow Thrower Birth defects or other mproductNe harm Warranty Statement Storage Safety RulesWash Hands After Handling Preparation Operation TrainingControl and Operating Symbols Maintenance and StorageEcL Stop Contents of Parts BAG Actual Size Knifeto outcarton Tools Required for AssemblyTo Remove Snow Thrower from Carton UpperHandle remove To Assemble the Handle Crank AssemblyEye Bolt Ratwasher HOW to SET the Skid Height HOW to Assemble the Chute DeflectorHOW to SET the Length of the Cables Checkust Know Your Snow Thrower Choke Control Gas PrimerCap Button SafetyStarter To Stop Your Snow Thrower HOW to Move Forward and BackwardTo Control Snow Discharge To Throw SnowBefore Starting the Engine Check the OILFill GAS To Stop Engine To Start EngineRecoilStarter Receptacle PowerCordFrozen Starter Snow Throwing Tips To Remove Snow from AugerGeneral Recommendations Customer ResponsibilitiesAfter Each USE Snow Thrower Engine SpecificationsLubrication EngineSpark Plug To Change Engine OILTo Adjust Scraper BAR To Adjust Skid HeightSpark k HOW to Remove Snow HoodCafouretor Inch Belt AdjustmentEngaged Jure28 HOW to Replace the BeltsSpdng Traction DriveBelt DrivePulley Engine Ring Swing PlateInstall the belt cover.Tighten screw see HOW to Check Adjust the Cables Belt Guide AdjustmentAuger Drive Cable Adjustment CableAdjustment Traction Drive Cable AdjustmentBracket Auger Housing Speed ControlRod HOW to Adjust or Replace the Friction WheelChain Check the adjustment of the friction Spacer HOW to Replace Auger Shear BoltEngine OtherTrouble Cause Correcon Sears .Emission Control Defects Warranty Coverage Cold start enrichment sys Typicallyfoundona certifiedengine Craftsman 24 6HP Snow Thrower 536.881550 Engine Ref, DrivePage Ref. Auger HousingPage25-220 13 14 25-329 Description KeyCraftsman 24 6HP Snow Thrower 536.881550 Frame Craftsman 24 6HP Snow Thrower 536.881550 Gear Case 236 Craftsman 24 6HP Snow Thrower 536.681550 Drive218 207 NU,IEPS HE I/4-20 Craftsman 24 6HP Snow Thrower 536.881550 DriveCraftsman 24 6HP Snow Thrower 536.881550 Discharge Chute Ref.Auger HousingPage6O3 601 6O9Washer Chute AssemblyKNOB, Wing Bolt49O5OO527 Craftsman 24 6HP Snow Thrower 536.881550 Auger Housing522 523SPACER,FRICTION Pulley BRUSH, CleanoutRETAINER,BALLBRNG BEARING,BALL73O 729 74O Craftsman 24 6HP Snow Thrower 536.881550 Handle746 762Craftsman 24 6HP Snow Thrower Handle Craftsman 24 6HP Snow Thrower 536.881550 Chute ROD Ref.Auger HousingAssy852-10 GROMME, EYE Bolt Craftsman 24 6HP Snow Thrower 536.881550 Shift Yoke Decals Craftsman 24 6HP Snow Thrower 536.881550 Wheels O410111L55 Briggs & Stration Engine Ring Set Briggs & Stratton Engine40 692194 Retalnar-Valve 45 690977 Tappet-Valve S92I 51%BowlVent Key No. PartNo. DescdptionGasket-Intake Required 95 691636 Screw J613Y 1095 638215 Gasket Set-Valve 1196 696692 Screw 309 696818 Motor-Starter 316 690370 Screw1211 496144 Pulley/Spring Starter Shield0410111L62 Almacenamiento Del solhaos que el combusdble CAPACITACI6NPermitsque el motory el quitanlevesse ManeJeel combustiblecon cuidado.ste es sitamente inflamableAlejadode la bujlapare evitarun arran- que accidental Mantenimiento Y AlmacenamientoDespaelo Patpldo Sjmbolos DE Control Y OPERACI6NAnanque de motor ColeorAbajo Arriba Izquierda Derecha Sjmbolos DE Control Y OperacinPeugro PeligroContenido DE LA Bolsa DE Partes Famaiioreal Como Sacar EL Quitanieves DE LA Caja Herramientas NecesariasPalancade propulsibn De la barrena Portran Cabledd embmgue Palanca de PatinasdeC6MO Ensamblar EL Mango Y EL Conjunto DE LA Manivela C6MO Ajustar LOS Patines DE Altura CMO Ensamblar EL Deflector DEL Tubo DE DescargaCMO Establecer LA Longitud DE LOS Cables USTADEREVISI6N Avs Conozca SU QuitanievesC6M0 Controlar LA Descarga DE C6M0 Avanzary RetrocederLanzamiento DE Nieve C6MOUSAR EL Pasador DE Enganche DE LA RuedaAntes DE Encender EL Motor MotorAntes DE Arrancar EL Motor CombustibleArranque DEL Motor Parada DEL MotorCarel motor,asegresede haberleido la informacl6nsiguiente Enchufedel cord6n C6mo hacerarrancarel motorenfri0Manlt,e arran- de alimentad6n Qua manualArranque Congelado MaHJadel ananquemanuaJse enrolls lentamerrteConsejos Sobre EL Lanzamiento C6MO Quitarla Nievey Escombrosatascadosdela BarrenaSuelte la palancade propulsi6nde la ba DE NieveResponsabilidadesdel Propietario Recstrosde Serwcio Capadtadasoesab doreparacbRecomendaciones Generales Motor ESPEClRCAClONES BUJiA MotorLlenofull Cambio DE AceitePatnde ajuste AloJamlentode altura de la barrena Rgura El arranque accidental del moAjuste DE LA Barra Raspadora Como Desmontar LA Cubierta Protectora Guta Puesta Ajuste DE I.AS CorreasVuelva a poner la cubierta de la C6MO Reemplazar LAS CO- Rreas0410111L86 Figura PoleaMamas de alinearnlento Figure Como Revisar Y Ajustar LOS Cables Ajustesdela CorreagujaAjustes DEL Cable DE PROPULSI6N C6MO Ajustar 0 Reemplazar LA Rueda DE Friccin Fura Figura88 De partesencontrarpemosde seguridad adicionales C6MO Reemplazar LOS Pernos DE Seguridad DE LA BarrenaMotor QuitanievesOtras Indicaciones CORRECClON Problema CausaSu sisternade controlde emisionesinclwe Laina ea mnte ened Us deAm6ricaydtUstedincluyondoel dlagn6stico,laspartesy la mano de obra Sin Costo BujasEs necesadose g Duranteel periodode lagarang=,CualquierO410111L99 Sears Parts and Repair Center Anytime,dayornightU.S.A.only Your HomeMY-HOME Anytime, day or night Canada

536.88155 specifications

The Craftsman 536.88155 is a snowblower that has gained a reputation for its efficiency and reliability in tackling winter’s harsh conditions. Designed for residential use, this model stands out with its powerful engine and user-friendly features, making it a popular choice among homeowners looking to keep their driveways and walkways clear of snow.

One of the standout features of the Craftsman 536.88155 is its potent 27-inch clearing width. This allows users to cover a larger area in less time, reducing the physical effort required when dealing with heavy snowfall. The snowblower is equipped with a powerful engine that provides outstanding performance, ensuring that it can handle even the most challenging snow conditions with ease.

A key characteristic of the Craftsman 536.88155 is its capability to throw snow at impressive distances. The machine is designed with an adjustable chute that allows users to direct snow where they want it. This feature is particularly useful for preventing snow from being thrown back onto cleared paths, ensuring a cleaner finish. The chute can be easily adjusted from the operator's position, adding to the overall convenience in usage.

The Craftsman 536.88155 employs a user-friendly design that includes electric start capability. This feature eliminates the hassle of struggling with pull cords on cold mornings, allowing users to simply plug in and start the machine with the push of a button. Additionally, the ergonomic handles and controls enhance comfort and ease of use, making it suitable for individuals of varying physical abilities.

In terms of build quality, the Craftsman 536.88155 boasts a durable construction designed to withstand harsh winter conditions. The snowblower is made from high-quality materials that promote longevity while reducing maintenance needs. Its heavy-duty construction ensures stability, enabling it to navigate through both light and heavy snow effectively.

With its combination of power, user-friendly features, and durable construction, the Craftsman 536.88155 serves as an excellent tool for ensuring winter mobility and safety. Whether you are dealing with light flurries or a significant snowfall, this reliable snowblower is equipped to handle the task efficiently, making it a worthwhile investment for homeowners facing the challenges of winter weather.
Top Page Image Contents