Craftsman 536.88614 manual Fill OIL, Fill GAS, Before Starting the Engine

Page 11

For ease of maneuverability in light snow conditions, disconnect the klick pin from the wheel locked position and push into the single wheel drive (klick pin through axle hole only) position (see figure below).

Make sure that the klick pin is in the single wheel drive position of the axle only and not through the locked position.

Unlocked

Position

KlickPin

Single Wheel Drive

BEFORE STARTING THE ENGINE

FILL OIL

NOTE: Engine may already contain some

residual oil. Check frequently when filling the crankcase. Do not over fill. This snow

thrower was shipped with a container of 5W30 motor oil. This oil must be added to

the engine before operating. Remove the oil fill cap/dipstick and fill the crank case to (FULL) line on dipstick (20 ounces) (see next figure).

Tighten the fill cap/dipstick securely each time you check the oil level.

For extreme cold operating conditions of 0°F and below, use a partial synthetic 0W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting easier in areas where the temperature is 20 ° F. or lower.

Fill/Dipstick

NOTE: Oil level must be

between full and add mark.

FILL GAS

NOTICE: ENGINES WHICH ARE CERTI-

FIED TO COMPLY WITH CALIFORNIA AND US EPA EMISSION REGULATIONS

FOR ULGE ENGINES: Are certified to op- erate on regular unleaded gasoline. Include the following emission control system(s):

EM, TWC (if so equipped). Include any user adjustable features - therefore no other ad- justmants are needed.

WARNING: Experience indicates that alco- hol blended fuels (called gasohol or those using ethanol or methanol) can attract moisture which leads to separation and for- mation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Start the engine and let it run until the fuel lines and carburetor are empty. Use the carburetor bowl drain to empty residual gasoline from the float chamber. Use fresh fuel next season (see

Storage instructions on page 22 for addi- tional information).

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Fill the fuel tank with a fresh, clean, un- leaded regular, unleaded premium, or reformulated automotive gasoline only. DO NOT use leaded gasoline. Be sure that the container you pour the gasoline from is clean and free from rust or other foreign particles. Never use gasoline that may be

stale from long periods of storage in the container.

/_ CAUTION: Gasoline is flammable and

caution must be used when handling or stor_ ing it.

Do not fill fuel tank while snow thrower is

running, when it is hot, or when snow thrower is in an enclosed area.

Keep away from open flame or an electrical

spark and DO NOT SMOKE while filling the fuel tank.

NEVER fill the tank completely. FILL THE TANK to within 1/4" - 1/2" from the top to provide space for expansion of fuel.

Always fill fuel tank outdoors and use a fun- nel or spout to prevent spilling.

11

Image 11
Contents Crrftsmrw Preparation Limited TWO-YEAR Warranty on Craftsman Snow ThrowerTraining Expand OperationExtended period Maintenance Andstorage= Clutch Able Height adjust 16 X To Install the Upper Handle and Crank AssemblyTo Remove Snow Thrower from Carton Control Cables To Assemble Snow ChuteHOW to SET UP Your Snow Thrower ChecklistStop Know Your Snow ThrowerTo USE Wheel Lockout PIN Howto Useyour Snow Thrower To Stop Your Snow ThrowerTo Control Snow Discharge BackwardBefore Starting the Engine Fill OILFill GAS Cold Start To Stop EngineSnow Throwing Tips Cold StartWarm Start Frozen Recoil StarterRJ19LM Customer Responsibilities Service Schedule Records DatesProduct Specifications Horse Power 5HP Displacement Park PlugLubrication Every 25 Hours Generalrecommendationssnow ThrowerAfter First USE OIL Recommendation LubricationEngine Lubrication To Adjust Scraper BAR To Adjust Skid HeightTo Adjust the Clutch Control Cables To Replace Belts To Adjust Belts Auger Drive BeltAuger Drive Belt Traction Drive BeltTo Adjust the Belt Guides To Adjust the Friction WheelTo Replace Auger Shear Bolt To Replace Friction WheelTo Replace To AdjustcarburetorTo Adjust or Replace Spark Plug To AdjustOther Snow Thrower StorageEngine Storage Trouble Cause Correction Unit fails to discharge snowScrew #6-32x2.50 Electric Start Assembly Part NameEngine Assembly Artno Partname Part Name Craftsman 22 -5H.P.SNOW Thrower Frame Assembly Washer, Sp Drive AssemblyGear Case Assembly @ @ Auger Housing AssemblyPart NO. Part Name Discharge Chute Assembly Part NameBOO Part Name Refi Handle AssemblyNO. Part no 579857 Wheel AssemblyDecals Chute Control ROD Assembly20A 640053 Idle Restrictor Screw CAP Craftsman 4-CYCLE Engine Model NumberCraftsman 4-CYCLE Engine Modee Number IEF. I PART# EF. PART# I Part Name13 590574 HANDLE, Starter REF. PART# Part Name STARTER, RewindStarter no E REF. PART# Craftsman 4-CYCLE Engine Model Number 143,985003Page Lll