Craftsman 247.8819 operating instructions Belt Replacement, Chute Bracket, Auger Belt

Page 19

SERVICE AND MAINTENANCE

Chute Bracket

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so:

1. Loosen the two nuts which secure the chute bracket and reposi- tion it slightly. See Figure 20.

2. Retighten the nuts.

Auger Control

Refer to the Assembly section for instructions on adjusting the auger control cable.

Skid Shoes

Refer to the Assembly section for instructions on adjusting the skid shoes.

Belt Replacement

Figure 20

Auger Belt

To remove and replace your snow thrower’s auger belt, proceed as follows:

1. To prevent spillage, place a piece of plastic wrap under the gas cap and tighten securely.

2.Remove the plastic belt cover on the front of the engine by remov- ing the two self-tapping screws. See Figure 21.

3.Roll the auger belt off the engine pulley. See Figure 22.

4.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

Figure 21

Figure 22

Image 19

Contents 2007 Operator’s ManualWarranty Statement Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Operation Maintenance & StorageThis page left intentionally blank USE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsLoose Parts AssemblyAssembly Removing From CartonAssembly Tire Pressure AdjustmentsChute Clean-Out Tool Set-UpAuger Control Chute AssemblyChoke Control OperationEngine Controls Shift Lever Ignition KeyElectric Starter Button Chute AssemblyThrottle Control Recoil Starter HandleBefore Starting Engine Clean-Out ToolStarting The Engine To Engage Augers Replacing Shear PinsStopping The Engine To Engage DriveChecking Engine Oil Service and MaintenanceChanging Engine Oil Lubrication Shift Cable Shave Plate and Skid ShoesDrive Control Chute Bracket Belt ReplacementAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Each Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesShort-Term Storage OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTroubleshooting Craftsman Snow Thrower Model Parts ListDescription 418 1232 Pivot Rod Parts List 790-00289A Plt., Cvr Craftsman Engine Model LH318SA-156587 For Snow Thrower Model Governor Shaft Blower Housing Baffle Screw, 1/4-20 x 19/32 Lock Nut 35980AScrew, 10-32 x 3/4 29918 Lock Nut 2964231342 33877 Intake Pipe34667 Governor Link 36652 Choke Spring Control Bracket Incl , 203, 20420A Rewind Starter 35450 Housing AssemblyElectric Starter 110 Volt optional Gear & Nut Incl 35449This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Número DE Modelo ÍndiceDeclaración DE Garantía Especificaciones DEL ProductoAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Mantenimiento y almacenamiento OperaciónMOntaje MontajeExtracción de la unidad de la caja Partes sueltasSitúe el montaje del canal sobre la base. Vea la figura Presión de los neumáticos ConfiguraciónAjustes Herramienta de Limpieza del CanalPrueba de control de la barrena Ajuste del montaje del canalVuelva a apretar la tuerca hexagonal superior Llave de encendido Palanca de cambiosOperación Controles del motorSalida del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Botón del arrancador eléctricoEncendido del motor Control direccional del canalHerramienta de limpieza Antes de encender el motorArrancador de retroceso Detención del motorProcedimiento para engranar la transmisión Procedimiento para engranar las barrenasMantenimiento de Motor Servicio Y MantenimientoTapón para drenado de aceite Lubricación Para retirar las zapatas antideslizantes Cable de cambiosPlaca de raspado y zapatas antideslizantes Control de la transmisiónLa Correa de la barrena Reemplazo de la correaSoporte del canal Control de la barrenaFigura La correa de la transmisiónExtracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarAlmacenaje a Corto plazo Almacenamiento Fuera DE TemporadaPreparación del motor Preparación de la máquina quitanieveSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Get it fixed, at your home or ours

247.8819 specifications

The Craftsman 247.8819 is a highly versatile and robust lawn mower designed for homeowners seeking a reliable and efficient tool to maintain their lawns. This mower stands out due to its impressive features, advanced technologies, and thoughtful characteristics that cater to both novice and experienced users.

One of the main features of the Craftsman 247.8819 is its powerful engine. Equipped with a reliable gas engine, it offers strong performance and the capability to tackle tough grass, ensuring a clean and precise cut every time. The high torque output allows this mower to handle various terrains with ease, making it a perfect choice for yards of different sizes and complexities.

Another remarkable feature is its variable speed transmission. This technology allows users to adjust the speed of the mower according to their comfort and specific mowing requirements. With the ability to operate at different speeds, users can maneuver through tight corners or open spaces more effectively, making for a more efficient mowing experience.

The cutting deck of the Craftsman 247.8819 is designed to provide optimal cutting performance. With a generous width, it enables users to cover more ground in less time. Additionally, it features multiple height adjustment settings, allowing for customized cutting heights to promote healthy grass growth. Whether users prefer a low cut for a manicured lawn or a higher cut for a more natural look, this mower can adapt accordingly.

Comfort and ease of use are also prioritized in the Craftsman 247.8819. Its ergonomic handles are designed to minimize strain during operation, and the mower's lightweight construction ensures easy maneuverability. Moreover, the mower is equipped with large, durable wheels that provide stability across varied terrains while ensuring smooth operation.

Maintenance is made simple with the Craftsman 247.8819. Its design promotes easy access to the engine and other components, allowing for straightforward maintenance tasks such as oil changes and blade sharpening. This ensures the mower remains in top condition and continues to perform efficiently over time.

In summary, the Craftsman 247.8819 offers a powerful engine, variable speed transmission, versatile cutting heights, and an ergonomic design, making it an excellent choice for homeowners. Its thoughtful features and ease of maintenance solidify its reputation as a dependable lawn mower for keeping lawns looking their best.