Craftsman 247.8819 operating instructions Troubleshooting

Page 25

TROUBLESHOOTING

WARNING

Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs.

This section addresses minor service issues. To locate the nearest Sears Service Center or to schedule service, simply contact Sears at 1-800-4-MY-HOME®.

Problem

 

Cause

 

Remedy

Engine fails to start

1.

Choke control not in ON position

1.

Move choke control to ON position.

 

2.

Spark plug wire disconnected

2.

Connect wire to spark plug.

 

3.

Faulty spark plug

3.

Clean, adjust gap, or replace.

 

4.

Fuel tank empty or stale fuel

4.

Fill tank with clean, fresh gasoline.

 

5.

Engine not primed.

5.

Prime engine as instructed in the Operation Section.

 

6.

Safety key not inserted.

6.

Insert key fully into the switch.

 

 

 

 

 

Engine runs erratically

1.

Engine running on CHOKE

1.

Move choke control to OFF position.

 

2.

Stale fuel

2.

Fill tank with clean, fresh gasoline.

 

3.

Water or dirt in fuel system

3.

Drain fuel tank. Refill with fresh fuel.

 

4.

Carburetor out of adjustment

4.

Contact your Sears Parts & Repair Center.

 

 

 

 

 

Engine overheats

1.

Carburetor not adjusted properly

1.

Contact your Sears Parts & Repair Center.

 

 

 

 

 

Excessive vibration

1.

Loose parts or damaged auger

1.

Stop engine immediately and disconnect spark plug

 

 

 

 

wire. Tighten all bolts and nuts. If vibration continues,

 

 

 

 

have unit serviced by a Sears Parts & Repair Center.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Connect and tighten spark plug wire.

 

2.

Gas cap vent hole plugged.

2.

Remove ice and snow from gas cap. Be certain vent

 

 

 

 

hole is clear.

 

 

 

 

 

Unit fails to propel itself

1.

Drive cable in need of adjustment

1.

Adjust drive control cable. Refer to Service and

 

 

 

 

Maintenance section.

 

2.

Drive belt loose or damaged

2.

Replace drive belt. Refer to Service and Mainte-

 

 

 

 

nance section.

 

 

 

 

 

Unit fails to discharge snow

1.

Chute assembly clogged.

1.

Stop engine immediately and disconnect spark plug

 

 

 

 

wire. Clean chute assembly and inside of auger

 

 

 

 

housing with clean-out tool or a stick.

 

2.

Foreign object lodged in auger.

2.

Stop engine immediately and disconnect spark plug

 

 

 

 

wire. Remove object from auger with clean-out tool

 

 

 

 

or a stick.

 

3.

Auger cable in need of adjustment.

3.

Adjust auger control cable. Refer to Assembly

 

 

 

 

section.

 

4.

Auger belt loose or damaged.

4.

Replace auger belt. Refer to Service and Mainte-

 

 

 

 

nance section.

 

5.

Shear pin(s) sheared.

5.

Replace with new shear pin(s).

 

 

 

 

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 2007 Operator’s ManualWarranty Statement Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Operation Maintenance & StorageThis page left intentionally blank USE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsAssembly AssemblyRemoving From Carton Loose PartsAssembly Chute Clean-Out Tool AdjustmentsSet-Up Tire PressureAuger Control Chute AssemblyEngine Controls OperationShift Lever Ignition Key Choke ControlThrottle Control Chute AssemblyRecoil Starter Handle Electric Starter ButtonBefore Starting Engine Clean-Out ToolStarting The Engine Stopping The Engine Replacing Shear PinsTo Engage Drive To Engage AugersChecking Engine Oil Service and MaintenanceChanging Engine Oil Lubrication Shift Cable Shave Plate and Skid ShoesDrive Control Chute Bracket Belt ReplacementAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Each Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesPreparing Engine OFF-SEASON StoragePreparing Snow Thrower Short-Term StorageTroubleshooting Craftsman Snow Thrower Model Parts ListDescription 418 1232 Pivot Rod Parts List 790-00289A Plt., Cvr Craftsman Engine Model LH318SA-156587 For Snow Thrower Model Screw, 10-32 x 3/4 29918 Blower Housing Baffle Screw, 1/4-20 x 19/32 Lock Nut 35980ALock Nut 29642 Governor Shaft34667 Governor Link 33877 Intake Pipe36652 Choke Spring Control Bracket Incl , 203, 204 3134220A Rewind Starter Electric Starter 110 Volt optional Housing AssemblyGear & Nut Incl 35449 35450This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Declaración DE Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Mantenimiento y almacenamiento OperaciónExtracción de la unidad de la caja MontajePartes sueltas MOntajeSitúe el montaje del canal sobre la base. Vea la figura Ajustes ConfiguraciónHerramienta de Limpieza del Canal Presión de los neumáticosPrueba de control de la barrena Ajuste del montaje del canalVuelva a apretar la tuerca hexagonal superior Operación Palanca de cambiosControles del motor Llave de encendidoManija del arrancador de retroceso Control del estranguladorBotón del arrancador eléctrico Salida del arrancador eléctricoHerramienta de limpieza Control direccional del canalAntes de encender el motor Encendido del motorProcedimiento para engranar la transmisión Detención del motorProcedimiento para engranar las barrenas Arrancador de retrocesoMantenimiento de Motor Servicio Y MantenimientoTapón para drenado de aceite Lubricación Placa de raspado y zapatas antideslizantes Cable de cambiosControl de la transmisión Para retirar las zapatas antideslizantesSoporte del canal Reemplazo de la correaControl de la barrena La Correa de la barrenaFigura La correa de la transmisiónExtracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarPreparación del motor Almacenamiento Fuera DE TemporadaPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Get it fixed, at your home or ours

247.8819 specifications

The Craftsman 247.8819 is a highly versatile and robust lawn mower designed for homeowners seeking a reliable and efficient tool to maintain their lawns. This mower stands out due to its impressive features, advanced technologies, and thoughtful characteristics that cater to both novice and experienced users.

One of the main features of the Craftsman 247.8819 is its powerful engine. Equipped with a reliable gas engine, it offers strong performance and the capability to tackle tough grass, ensuring a clean and precise cut every time. The high torque output allows this mower to handle various terrains with ease, making it a perfect choice for yards of different sizes and complexities.

Another remarkable feature is its variable speed transmission. This technology allows users to adjust the speed of the mower according to their comfort and specific mowing requirements. With the ability to operate at different speeds, users can maneuver through tight corners or open spaces more effectively, making for a more efficient mowing experience.

The cutting deck of the Craftsman 247.8819 is designed to provide optimal cutting performance. With a generous width, it enables users to cover more ground in less time. Additionally, it features multiple height adjustment settings, allowing for customized cutting heights to promote healthy grass growth. Whether users prefer a low cut for a manicured lawn or a higher cut for a more natural look, this mower can adapt accordingly.

Comfort and ease of use are also prioritized in the Craftsman 247.8819. Its ergonomic handles are designed to minimize strain during operation, and the mower's lightweight construction ensures easy maneuverability. Moreover, the mower is equipped with large, durable wheels that provide stability across varied terrains while ensuring smooth operation.

Maintenance is made simple with the Craftsman 247.8819. Its design promotes easy access to the engine and other components, allowing for straightforward maintenance tasks such as oil changes and blade sharpening. This ensures the mower remains in top condition and continues to perform efficiently over time.

In summary, the Craftsman 247.8819 offers a powerful engine, variable speed transmission, versatile cutting heights, and an ergonomic design, making it an excellent choice for homeowners. Its thoughtful features and ease of maintenance solidify its reputation as a dependable lawn mower for keeping lawns looking their best.
Top Page Image Contents