Husqvarna 5021 R, 5021 E manual ADD OIL to the Engine, ADD Fuel to the Engine

Page 12

ASSEMBLY

ADD OIL TO THE ENGINE

NOTE: Engine may already contain some residual oil. Check frequently when filling the crankcase. DO NOT overfill.

The snow thrower was shipped with a container of 5W30 motor oil. This oil must be added to the engine before operating.

OIl Fill Cap/Dipstick

Figure 2

NOTE: Oil level must be at FULL mark.

1.Make sure the unit is level.

2.Remove the oil fill cap/dipstick and fill the crankcase to “FULL” line on dipstick. DO NOT overfill.

3.Pour the oil slowly into the engine oil fill. DO NOT overfill. After adding oil, wait one minute and then recheck the oil level.

4.Tighten the oil fill cap/dipstick securely each time you check the oil level.

NOTE: Synthetic oil can assist with starting in extreme cold temperatures. Synthetic 5W30 is acceptable for all temperatures. Do NOT mix oil with unleaded gasoline.

ADD FUEL TO THE ENGINE

This engine is certified to operate on gasoline or petrol. The emissions control system for this engine is EM (Engine Modifications).

WARNING: Alcohol blended fuels (called gasohol or those using ethanol or methanol)

can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

NOTE: To avoid engine problems, the fuel system must be emptied before storage for 30 days or longer. Start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See the Storage section in this manual for additional information.

Fill the fuel tank only with fresh, clean, unleaded regular, unleaded premium, or reformulated automotive fuel with

DPLQLPXPRIRFWDQH'2127XVHOHDGHGJDVROLQH or petrol. Make sure that the container you pour the fuel is free from rust or foreign particles. Never use fuel that may be stale from long periods of storage in the container.

1.Stop the engine. Before you remove fuel cap, let the engine cool at least 2 minutes.

2.Remove the fuel cap. Fill the fuel tank to

DSSUR[LPDWHO\LQFKHV PP EHORZ top of neck to allow for fuel expansion. Be careful not to overfill.

3.Replace the fuel cap before starting the engine.

WARNING: Gasoline and petrol and its vapors are extremely flammable and explosive. Fire or

explosion can cause severe burns or death.

‡7XUQHQJLQHRIIDQGOHWHQJLQHFRRODWOHDVWPLQXWHV removing the gas cap.

‡)LOOIXHOWDQNRXWGRRUVRULQZHOOYHQWLODWHGDUHD

‡.HHSJDVROLQHDZD\IURPVSDUNVRSHQIODPHVSLORW lights, head, and other ignition sources.

‡,IIXHOVSLOOVZDLWXQWLOLWHYDSRUDWHVEHIRUHVWDUWLQJ engine.

1741506

12

Image 12
Contents Operator’s Manual Introduction Responsibility of the OwnerHazard Symbols and the meanings Rules for Safe OperationTraining Children Table of Contents Safety Decals Decals OWNER’S Information Warranty Statement Limited WarrantyItems not Covered by this Warranty Assembly Parts BAG ContentsTools Required for Assembly HOW to Remove the Snowthrower from the CartonADD OIL to the Engine ADD Fuel to the EngineBefore YOU Operate Know Your SnowthrowerControl and Equipment Features Figure OperationHOW to Control Discharge Snow HOW to Throw SnowHOW to Stop Discharging Snow HOW to Move ForwardHOW to Stop the Engine HOW to Start the EngineHOW to Start a Cold Engine Before Starting the EngineHOW to Start a Warm Engine HOW to Start a Warm Engine with a Frozen StarterHOW Clear a Clogged Discharge Chute Dry and Average Snow Maintenance Engine Power Rating InformationCustomer Responsibilities Emissions ControlHOW to Remove the TOP Cover Lubrication Before StorageHOW to Adjust the Auger Control Cable HOW to Remove the Belt CoverHOW to Replace the Drive Belt HOW to Replace the Auger HOW to Adjust the Brake PADHOW to Replace the Spark Plug HOW to Prepare the Snowthrower for StorageHOW to Order Replacement Parts Troubleshooting Chart Trouble Cause CorrectionEngine And Frame Assembly 0003REF no Description Engine And Frame Assembly SPACER, Drive Pulley Auger And Control Assembly 0005COVER, TOP Discharge Chute 0007Chute Ring Handle Assembly 0011HANDLE, Upper Chute Rod Assembly 0009ROD, Chute Decals 0015DECAL, Warning HOT Muffler Wheels 0013RING, Retainer E