Husqvarna 1330SB owner manual HOW to USE Your Snow Thrower, Stopping

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

TO USE CHOKE CONTROL (See Fig. 13)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move throttle control to “STOP” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 11)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 11

TO USE THROTTLE CONTROL (See Fig. 12)

The throttle control is located on the engine. Always operate the snow thrower with the engine at full throttle. Full throttle offers the best snow thrower performance.

FAST

SLOW

FIG. 12

10

OFFFULL

FIG. 13

TO CONTROL SNOW DISCHARGE (See Fig. 14)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and wait for all moving parts tostop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press down- ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to raise the deflector and increase the distance. Move lever back to lower the deflector and decrease the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 14

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 1330SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Recoil auxiliary starter handle used for startingHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting KEY Part Description Repair PartsAuger Housing / Impeller Assembly CARRIAGEBOLT5/16−18X.625Exploded Bearing Gearbox AssemblyImpeller Tool ClipAuger 30 RH Auger 30 LHSkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750Control Panel / Discharge Chute 532 40 59-32 Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyPulley Pivot Handles Lower TubeRepair Parts HandlesRear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Drive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX Shaft532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange BearingGear Axle ShaftRoll PIN 3/16 Clik PINRepair Partschassis / Engine / Pulleys 532 43 58-27 Steer Cable Bracket LH WheelsSteer Cable Bracket RH Wheel Lobe WheelsCover Axle LobeBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Repair Parts Decals532 42 95-90 DECAL, Remote Deflector Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 42 52-53 Rev 10.07.10 SR/TH

1330SB specifications

The Husqvarna 1330SB is a robust and versatile snow blower designed to tackle even the harshest winter conditions with efficiency and ease. Known for its durability and powerful performance, this model has become a popular choice among homeowners and professionals alike.

One of the standout features of the Husqvarna 1330SB is its 291cc engine, which delivers an impressive output for clearing snow. This powerful engine allows the machine to handle heavy snowfall, making it suitable for regions that experience significant winter weather. The electric start mechanism ensures that users can start the snow blower easily, even in frigid temperatures.

The 1330SB features a 30-inch clearing width, which enables it to clear large areas efficiently in a single pass. The high performance auger system is designed to break through ice and compacted snow, ensuring thorough and effective snow removal. The heavy-duty auger and impeller work in tandem to throw snow up to 50 feet away, making it perfect for clearing driveways, sidewalks, and larger areas without the need for multiple passes.

In terms of maneuverability, the Husqvarna 1330SB is equipped with power steering, allowing for easy navigation around obstacles. The adjustable handlebar adds an additional layer of comfort, enabling users to customize the height according to their preference. Furthermore, the track drive system enhances stability and traction, ensuring that the snow blower can handle uneven terrain and heavy snowfall without slipping.

The 1330SB also incorporates advanced features such as a remote chute rotation control, allowing users to easily direct the snow where they want it to go. This is particularly beneficial when clearing large areas or navigating around cars and other obstacles. The adjustable deflector ensures that snow can be thrown at various heights, adding to the versatility of this snow blower.

Lastly, the Husqvarna 1330SB is built with quality materials and superior engineering, ensuring longevity and robust performance year after year. Coupled with its powerful motor and user-friendly features, it stands out as an excellent investment for anyone looking to make winter snow removal a hassle-free experience. Whether you're managing a residential property or tackling a commercial snow clearing task, the Husqvarna 1330SB is equipped to deliver outstanding results.
Top Page Image Contents