Husqvarna 1330SB owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 1330SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Drive speed control lever used to select forward orStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting CARRIAGEBOLT5/16−18X.625 Repair PartsAuger Housing / Impeller Assembly KEY Part DescriptionExploded Tool Clip Gearbox AssemblyImpeller BearingAuger 30 RH Auger 30 LHSkid Plate CARRIAGEBOLT5/16−18X.750 Weight BARControl Panel / Discharge Chute 532 40 59-32 Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyPulley Pivot Lower Tube HandlesHandles Repair PartsRear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Drive HEX Shaft 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate WeldmentFlange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate GearClik PIN Axle ShaftRoll PIN 3/16 GearRepair Partschassis / Engine / Pulleys 532 43 58-27 Steer Cable Bracket LH WheelsSteer Cable Bracket RH Axle Lobe WheelsCover Wheel LobeRetainer PIN Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector Repair Parts Decals532 42 95-90 DECAL, Remote Deflector Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 42 52-53 Rev 10.07.10 SR/TH

1330SB specifications

The Husqvarna 1330SB is a robust and versatile snow blower designed to tackle even the harshest winter conditions with efficiency and ease. Known for its durability and powerful performance, this model has become a popular choice among homeowners and professionals alike.

One of the standout features of the Husqvarna 1330SB is its 291cc engine, which delivers an impressive output for clearing snow. This powerful engine allows the machine to handle heavy snowfall, making it suitable for regions that experience significant winter weather. The electric start mechanism ensures that users can start the snow blower easily, even in frigid temperatures.

The 1330SB features a 30-inch clearing width, which enables it to clear large areas efficiently in a single pass. The high performance auger system is designed to break through ice and compacted snow, ensuring thorough and effective snow removal. The heavy-duty auger and impeller work in tandem to throw snow up to 50 feet away, making it perfect for clearing driveways, sidewalks, and larger areas without the need for multiple passes.

In terms of maneuverability, the Husqvarna 1330SB is equipped with power steering, allowing for easy navigation around obstacles. The adjustable handlebar adds an additional layer of comfort, enabling users to customize the height according to their preference. Furthermore, the track drive system enhances stability and traction, ensuring that the snow blower can handle uneven terrain and heavy snowfall without slipping.

The 1330SB also incorporates advanced features such as a remote chute rotation control, allowing users to easily direct the snow where they want it to go. This is particularly beneficial when clearing large areas or navigating around cars and other obstacles. The adjustable deflector ensures that snow can be thrown at various heights, adding to the versatility of this snow blower.

Lastly, the Husqvarna 1330SB is built with quality materials and superior engineering, ensuring longevity and robust performance year after year. Coupled with its powerful motor and user-friendly features, it stands out as an excellent investment for anyone looking to make winter snow removal a hassle-free experience. Whether you're managing a residential property or tackling a commercial snow clearing task, the Husqvarna 1330SB is equipped to deliver outstanding results.
Top Page Image Contents