Husqvarna 1330SB owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity 4.0 Quarts (3,79 Liters)

and Type: Unleaded Regular only

Oil Type

SAE 5W-30 or 10W-30

(API SG–SL):

(0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces (0,74 Liters)

 

 

Spark Plug:

Champion RN4C

Gap:

0.030" (0,762 mm)

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

4-7

OPERATION

8-13

MAINTENANCE SCHEDULE

14

MAINTENANCE

14-15

SERVICE AND ADJUSTMENTS

16-18

STORAGE

19

TROUBLESHOOTING

20

REPAIR PARTS

21-40

3 WARRANTY

41-44

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 1330SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Drive speed control lever used to select forward orStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting CARRIAGEBOLT5/16−18X.625 Repair PartsAuger Housing / Impeller Assembly KEY Part DescriptionExploded Tool Clip Gearbox AssemblyImpeller BearingAuger 30 LH Auger 30 RHSkid Plate CARRIAGEBOLT5/16−18X.750 Weight BARControl Panel / Discharge Chute LEVER/CABLE Rotator Assembly 532 40 59-32 Rotator Pivot BracketPulley Pivot Lower Tube HandlesHandles Repair PartsClutch ROD Rear Plate13 532 41 54-33 Shifter Plate Bracket 532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightBulb Drive HEX Shaft 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate WeldmentFlange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate GearClik PIN Axle ShaftRoll PIN 3/16 GearRepair Partschassis / Engine / Pulleys Wheels 532 43 58-27 Steer Cable Bracket LHSteer Cable Bracket RH Axle Lobe WheelsCover Wheel LobeRetainer PIN Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY BAG of PartsRepair Parts Decals 532 18 10-35 DECAL, DANGER, Deflector532 42 95-90 DECAL, Remote Deflector Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 42 52-53 Rev 10.07.10 SR/TH

1330SB specifications

The Husqvarna 1330SB is a robust and versatile snow blower designed to tackle even the harshest winter conditions with efficiency and ease. Known for its durability and powerful performance, this model has become a popular choice among homeowners and professionals alike.

One of the standout features of the Husqvarna 1330SB is its 291cc engine, which delivers an impressive output for clearing snow. This powerful engine allows the machine to handle heavy snowfall, making it suitable for regions that experience significant winter weather. The electric start mechanism ensures that users can start the snow blower easily, even in frigid temperatures.

The 1330SB features a 30-inch clearing width, which enables it to clear large areas efficiently in a single pass. The high performance auger system is designed to break through ice and compacted snow, ensuring thorough and effective snow removal. The heavy-duty auger and impeller work in tandem to throw snow up to 50 feet away, making it perfect for clearing driveways, sidewalks, and larger areas without the need for multiple passes.

In terms of maneuverability, the Husqvarna 1330SB is equipped with power steering, allowing for easy navigation around obstacles. The adjustable handlebar adds an additional layer of comfort, enabling users to customize the height according to their preference. Furthermore, the track drive system enhances stability and traction, ensuring that the snow blower can handle uneven terrain and heavy snowfall without slipping.

The 1330SB also incorporates advanced features such as a remote chute rotation control, allowing users to easily direct the snow where they want it to go. This is particularly beneficial when clearing large areas or navigating around cars and other obstacles. The adjustable deflector ensures that snow can be thrown at various heights, adding to the versatility of this snow blower.

Lastly, the Husqvarna 1330SB is built with quality materials and superior engineering, ensuring longevity and robust performance year after year. Coupled with its powerful motor and user-friendly features, it stands out as an excellent investment for anyone looking to make winter snow removal a hassle-free experience. Whether you're managing a residential property or tackling a commercial snow clearing task, the Husqvarna 1330SB is equipped to deliver outstanding results.
Top Page Image Contents