Husqvarna ST 330T warranty To Remove Tracks See Fig, Carburetor, Engine Speed

Page 20

SERVICE AND ADJUSTMENTS

TO REMOVE TRACKS (See Fig. 28)

1.Remove cross brace by removing 2 bolts, lock washers and washers from the left and right track assemblies and pulling brace out.

2.Remove the 2 large springs attached to inside of tracks.

3.Remove the klik pin from axle.

4.Pull track off axle.

KLIK AXLE SPRING

PIN

BOLT

CROSS

BRACE

TRACK

ASSEMBLY WASHER LOCK

WASHER

FIG. 28

NOTE: For track replacement or for tension adjustments, contact an authorized service center/department

ENGINE

SEE ENGINE MANUAL.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a service center/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a service center/depart- ment, which has the proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 29)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 29

TO ADJUST TRACTION BELT AND AUGER BELT TENSION

If the traction or auger belt is slipping because it is not tight enough when engaged, the tension can be increased by adjusting the spring location in the control rod. Unhook the rod from the control lever and move the spring at the bottom of the rod one or two holes closer to the top of the rod. This effectively shortens the rod and increases the belt tension. (See "INSTALL AUGER CONTROL ROD" in the Assembly section of this manual.)

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Skid PlatesAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTransport and Height Adjustment of Snow Thrower SET Height Adjustment See FigsTo Transport See Figs Packed Snow Normal Operation Transport FloatHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To TransportADD Gasoline See Fig To Start EngineCold Start Electric Starter Warm Start Electric StarterSnow Throwing Tips Warm Start Recoil StarterBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Adjust Traction Belt and Auger Belt TensionTo Remove Tracks See Fig CarburetorInstructions for Adjusting Power Steering Cables See Figs Storage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below 06/17/2014 TH
Top Page Image Contents