Husqvarna ST 330T warranty Armor Protected Stamped Deck Shell Example Below

Page 27

 

Consumer Wheeled Limited Warranty Chart 2013

Exhibit A

 

 

Consumer (personal,

Commercial (any commercial,

Rental (any

 

 

household use only)

professional, institutional,

rental usage)

 

Product/Component

 

agricultural, or income producing use,

 

 

 

other than Rental Use)

 

Parts & Accessories (if purchased)

 

 

 

 

Accessories (e.g., grass catcher, bumper guard

 

 

 

 

accessories, etc.

1 Year

No Warranty

No Warranty

 

Parts (e.g., belts, blades, etc.)

90 days

No Warranty

No Warranty

Parts & Accessories (if replaced in Warranty Service)

 

 

 

 

Replacement parts and/or accessories provided

 

 

 

 

under this Limited Warranty are warranted only

 

 

 

 

for the BALANCE of the warranty period

 

 

 

 

applicable to the part or accessory that was

 

 

 

 

replaced.

See to left

See to left

See to left

 

 

Consumer

Commercial

Rental

*See Separate Engine Manufacturer's or Manufacturer's warranty. LCT Engines on specific Snow Throwers & Tillers, warranty through Husqvarna.

**See reference 4 (b) of the warranty statement.

RZ - Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.

EZ - One (1) Year Commercial warranty, parts & labor, with Husqvarna.

Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.

MZ - (ZT3100 Transmission) One (1) Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network. (ZT3100 Transmission) Two (2) Years Consumer warranty, parts & labor, with Hydro-Gear Distributor network.

M-ZT - (ZT3400 transmission) Two (2) Year warranty, parts & labor, with Hydro-Gear Distributor network.

***"Limited Lifetime Warranty" on Tiller tines and Fabricated Deck shell is for the life of the product or 7 (seven) years after the last date of the complete unit's final production, whichever comes first. Deck Shell replacement will be limited to a maximum of two (2) decks within the Limited Lifetime Warranty.

Armor Protected Stamped Deck Shell Example Below

Fabricated Deck Shell Example Below

Armor Protected

Stamped Deck Shell below, NOT reinforced

Stamped Deck Shell

 

Reinforced area

 

No reinforced area

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Skid Plates Parts Packed Separately in CartonUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsPacked Snow Normal Operation Transport Float Transport and Height Adjustment of Snow ThrowerSET Height Adjustment See Figs To Transport See FigsStopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Transport Before Starting the EngineWarm Start Electric Starter ADD Gasoline See FigTo Start Engine Cold Start Electric StarterIf Recoil Starter has Frozen Snow Throwing TipsWarm Start Recoil Starter Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Adjust Traction Belt and Auger Belt Tension To Remove Tracks See FigInstructions for Adjusting Power Steering Cables See Figs Engine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below 06/17/2014 TH
Top Page Image Contents