Husqvarna 11524E, 96193006600 manual Engine, Cleaning

Page 16

MAINTENANCE

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klik pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 11524E Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonEXT RA Shear Bolts and Nuts Rotator Head MountingAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Snow Throwing Tips Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Service Notes 435889 04.30.10 TH

96193006600, 11524E specifications

The Husqvarna 11524E (model number 96193006600) is a robust, reliable snow blower designed to tackle winter's worst conditions with ease. As part of its commitment to quality engineering and performance, Husqvarna has integrated advanced features and technologies that set this machine apart from competitors.

One of the standout characteristics of the Husqvarna 11524E is its powerful 24-inch clearing width, which allows for efficient snow removal on driveways, sidewalks, and large areas. Powered by a reliable Husqvarna engine, the snow blower delivers ample power to handle heavy, compacted snow. The electric start feature ensures that starting the machine is a breeze, even in frigid temperatures.

The 11524E is equipped with an impressive two-stage snow throwing system. Its first stage consists of an auger that breaks up and collects snow, while the second stage uses an impeller to discharge snow conveniently up to 40 feet away. This dual system efficiently moves large volumes of snow, making quick work of even the heaviest snowfalls.

Another notable feature of this model is its 180-degree rotating chute, allowing users to easily direct the snow where they want it. This level of control makes it suitable for use in tight spaces, ensuring that snow is not thrown onto walkways or back onto areas that have already been cleared.

The Husqvarna 11524E also prioritizes user comfort and ergonomics. The adjustable handle height, along with the heated grips, provides comfort during prolonged use in cold conditions. The heavy-duty tires ensure excellent traction and mobility on snowy surfaces, even on inclines or uneven terrain.

Durability is a key consideration in the design of the 11524E. The materials used in its construction are robust, ensuring that it can withstand the rigors of winter use. In addition, the design incorporates features that simplify maintenance, such as easily accessible belts and other components.

Overall, the Husqvarna 11524E (96193006600) stands out for its combination of power, performance, and user-friendly features. Designed to meet the demands of winter snow removal, it is a valuable asset for homeowners looking to maintain clear pathways and driveways during the snowy season. Whether handling light flurries or heavy snowfalls, this snow blower is equipped to deliver reliable results every time.
Top Page Image Contents