Husqvarna 11524E, 96193006600 manual To Replace Belts See Fig

Page 18

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 24)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6. REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 24

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 11524E Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head MountingRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Before StoppingIf Recoil Starter has Frozen Snow Throwing Tips Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Service Notes 435889 04.30.10 TH

96193006600, 11524E specifications

The Husqvarna 11524E (model number 96193006600) is a robust, reliable snow blower designed to tackle winter's worst conditions with ease. As part of its commitment to quality engineering and performance, Husqvarna has integrated advanced features and technologies that set this machine apart from competitors.

One of the standout characteristics of the Husqvarna 11524E is its powerful 24-inch clearing width, which allows for efficient snow removal on driveways, sidewalks, and large areas. Powered by a reliable Husqvarna engine, the snow blower delivers ample power to handle heavy, compacted snow. The electric start feature ensures that starting the machine is a breeze, even in frigid temperatures.

The 11524E is equipped with an impressive two-stage snow throwing system. Its first stage consists of an auger that breaks up and collects snow, while the second stage uses an impeller to discharge snow conveniently up to 40 feet away. This dual system efficiently moves large volumes of snow, making quick work of even the heaviest snowfalls.

Another notable feature of this model is its 180-degree rotating chute, allowing users to easily direct the snow where they want it. This level of control makes it suitable for use in tight spaces, ensuring that snow is not thrown onto walkways or back onto areas that have already been cleared.

The Husqvarna 11524E also prioritizes user comfort and ergonomics. The adjustable handle height, along with the heated grips, provides comfort during prolonged use in cold conditions. The heavy-duty tires ensure excellent traction and mobility on snowy surfaces, even on inclines or uneven terrain.

Durability is a key consideration in the design of the 11524E. The materials used in its construction are robust, ensuring that it can withstand the rigors of winter use. In addition, the design incorporates features that simplify maintenance, such as easily accessible belts and other components.

Overall, the Husqvarna 11524E (96193006600) stands out for its combination of power, performance, and user-friendly features. Designed to meet the demands of winter snow removal, it is a valuable asset for homeowners looking to maintain clear pathways and driveways during the snowy season. Whether handling light flurries or heavy snowfalls, this snow blower is equipped to deliver reliable results every time.
Top Page Image Contents