Husqvarna 96193006600, 11524E manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

4.0 Quarts (3,79 Liters)

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 5W-30 or 10W-30

(API SG–SL):

(0°F to +40°F / –18°C to +5°C)

 

Synthetic SAE 5W-30 or 10W-30

 

(below 0°F / –18°C)

 

 

Oil Capacity:

28 Ounces (0,8 Liters)

 

 

Spark Plug:

Champion QC12YC

Gap:

0.030" (0,762 mm)

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

5-7

OPERATION

8-14

MAINTENANCE SCHEDULE

15

MAINTENANCE

15-16

SERVICE AND ADJUSTMENTS

17-19

STORAGE

20

TROUBLESHOOTING

21

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 11524E Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and NutsUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine To Start Engine Before StoppingIf Recoil Starter has Frozen Snow Throwing Tips Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Service Notes 435889 04.30.10 TH

96193006600, 11524E specifications

The Husqvarna 11524E (model number 96193006600) is a robust, reliable snow blower designed to tackle winter's worst conditions with ease. As part of its commitment to quality engineering and performance, Husqvarna has integrated advanced features and technologies that set this machine apart from competitors.

One of the standout characteristics of the Husqvarna 11524E is its powerful 24-inch clearing width, which allows for efficient snow removal on driveways, sidewalks, and large areas. Powered by a reliable Husqvarna engine, the snow blower delivers ample power to handle heavy, compacted snow. The electric start feature ensures that starting the machine is a breeze, even in frigid temperatures.

The 11524E is equipped with an impressive two-stage snow throwing system. Its first stage consists of an auger that breaks up and collects snow, while the second stage uses an impeller to discharge snow conveniently up to 40 feet away. This dual system efficiently moves large volumes of snow, making quick work of even the heaviest snowfalls.

Another notable feature of this model is its 180-degree rotating chute, allowing users to easily direct the snow where they want it. This level of control makes it suitable for use in tight spaces, ensuring that snow is not thrown onto walkways or back onto areas that have already been cleared.

The Husqvarna 11524E also prioritizes user comfort and ergonomics. The adjustable handle height, along with the heated grips, provides comfort during prolonged use in cold conditions. The heavy-duty tires ensure excellent traction and mobility on snowy surfaces, even on inclines or uneven terrain.

Durability is a key consideration in the design of the 11524E. The materials used in its construction are robust, ensuring that it can withstand the rigors of winter use. In addition, the design incorporates features that simplify maintenance, such as easily accessible belts and other components.

Overall, the Husqvarna 11524E (96193006600) stands out for its combination of power, performance, and user-friendly features. Designed to meet the demands of winter snow removal, it is a valuable asset for homeowners looking to maintain clear pathways and driveways during the snowy season. Whether handling light flurries or heavy snowfalls, this snow blower is equipped to deliver reliable results every time.
Top Page Image Contents